NordicTrack Answered Questions & Fixed Issues

My wife had the same problem with her treadmill. I turned the beast on it's side, and unscrewed the plastic casing that houses the motor, computer, and all the electronics to the treadmill. I unplugged the incline/decline motor. Then on the bottom of the treadmill the long threaded rod that causes the incline needed to be moved. So I unbolted it from the catch, and manually screwed the rod back in with a wrench. Now the treadmill works fantastically, of course the incline/decline mechanism has been disabled, but I would rather have a treadmill with the incline disabled than have one always on 100% incline. Hope you found this helpful :)

I think you may need to put it in fold mode first...it may be in incline mode.

see the video attached and fix it. God bless you

Very hard to do unless you know how. to hard to tell in a email.go to Icon Fitness and look at the manual.

Nordictrack Audio Strider 600 Manual

see the video attached. lube too the rollers bearing front+back and fix it. God bless you

go to the next places1) www.fitnessrepairparts.com2) www.treadmilldoctor.comGod bless you

1) replace the batteries by new one with alkalines type and using the same polarities DO NOT use another mark example sony vs everyready. Clean the contacts batteries.2) Adjust the REED swtich, clean it, tight the connector very well, see the diagram and proceed.God bless you

Adjust the REED swicht , see diagram, clean it, and tight the plug very well.2) clean the ribbon cables, for keypads, clean it.3) tight the connector from display board vs lower board too see the block diagramAfter you fix it. RUN the software calibration for diagnostic, troubleshooting. tooGod bless you

1) adjust the REED switch, see the diagram clean it, tight the connector wires.2) Lube the deck belt very well. VERY IMPORTANT3) Lube the rollers bearing too, 4) Test the input voltage motor, if there are the Motor need repair5) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty.God bless you

1) test the outlet wall, put some desk lamp, and see if turn ON the light, is does the circuit is o.k if NOT the circuite is missing , Reset The c.breaker from your house or replace the blown fuse.2) if everything is o.k, turn ON the treadmill, if does work test the fuse blown y/o reset the c.breaker see the block diagram +diagram3) test the main switch for loose wires, or bad contacts, or faulty swithc.4) see any wires loose, maybe broken, or break, tight very well, see if some animal byte some wires connector. repair and TURN ON again.5) adjust the REED switch, see the diagram clean it, tight the wires connector well.Try again. God bless lyou

1) if your display use batteries ,replace by new ones.2)tight the flexible cord from keypanel vs display board3)tight the display board vs lower board( main motor board)4)see if your have 5VDC to display board coming from lower board.5) Test the lower board is coming the power 115 VCA + 5vdc COMING from power supply (transformer+ diodes+capacitor).6) Display board is faulty or Main Board(Lower board). Of course after you did check the step before. See the block diagram that I did for your illustration.Sincerely. Good luck, G-d bless you.ERNESTO CUADRAMANAGUA,NICARAGUA. C.A

1) YOU HAVE A COMBO PROBLEM: MECHANICAL+ ELECTRICAL*ELECTRONICS2) ROLLER BEARING DEFECTIVE3)BEARING MOTOR DEFECTIVE.Electrical:a)main motorb) TRANSFORMERC) COILD) capacitor faultyelectronic:a) main motor controller faulty.see the block diagram and test according , the main motor board has aprox 90% of functions of any treadmill. Sincerely. Good luck, and G-d bless you.ERNESTO CUADRAMANAGUA,NICARAGUA

1) I am assuming that the breaker is the treadmill and Not from your house.2)you must test the Main Motor. measure the voltage without load 3)now you must test the main motor controller board.4) transformer.test .see the block diagram and see how the main motor board has aprox 90% of functions of any treadmill.Good luck. Sincerely. G-d bless youERNESTO CUADRAMANAGUA, NICARAGUA C.A

go to www.ifit.com to the section support, and see the best description for you adjustment or troubleshooting for your display.Will be a good idea, to tigh the flexible cord for loosing cable,a dn try to proof.Otherwise will be go Ifitt. Good luck, G-d bless you, sincerelyERNESTO CUADRAMANAGUA, NICARAGUA

I just had the same problem. Of course tech support is closed so I sent an email. We'll see if they get it fixed tomorrow.

hi,
There are two possibilities for this problem
1. Check the speed sensor on near the motor pulley. Remove the sensor and clean it and re-fix it. then make a try. if problem remains then
2. The motor speed controller is faulty. There is an IGBT for controlling the motor speed. If it get shorted the motor will run it its high speed.

Be sure before opening the treadmill remove the power.
ok

well the reed switch is working but sounds like board or both check voltage coming to the console. wire harness. not sure but if it reads low controller iisue

This sounds like a static electricity problem.
First, check your outlet for a proper ground connection.
Be sure that the ground pin on the plug has not been removed.
Depending on the model, a number of machines came with connecting clips to ensure that the upper console was grounded. They were installed during the time of assembly between the frame and console. Check your manual assembly instructions to see if yours is one of these, and check to be sure they have been installed.

you will need to attach star washers to the rear roller bolts, they are having an issue with the lock washers they put on the rear roller bolts. Replace them with star washers. Tighten belt until it can be lifted about 2"-3" in the center.