NordicTrack Popular Questions, Answers, Tips & Manuals

The motor control board would be faulty. If you wish to get some details about treadmill repair ; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

First find out how many hours on the machine, if over 200 be cautious

the motor drive assembly is seperate from all the electronics that you program and the incline motor ,although it may not work if there is a "Saftey 'Clip that attaches to the machine and clips on yourself it wont work without this "or if this Magnetic Clip is 'Faulty, If you can lay Machine down on its side or look for a plastic cover at the front or underneith and see if you can Unscrew and access the motor ..there may be a Overload Reset Button or Fuse just after where the Main Power Cord goes into the Tredmill. tred mills also are common for getting pet fur and hair in the motor which can get caught up in the Brushes, (I Think it is Most likely a Fuse or overload switch that is inline with the main Drive Motor.(if you can post exact Model# of TREDMILL I can have a look at the Electrical Diagram and make a more accurate conclusion ,Cheers!

If you wish to get some details about treadmill repair ; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

There is a procedure for adjusting the treadmill belt. Almost all the treadmill follows the same procedure. If you wish to know how to adjust the treadmill belt properly then check the below added link. Even after that if you face the same problem then you have replace the running belt of your treadmill. http://electro-medical.blogspot.com/

If you wish to get some details about treadmill repair then check the below mentioned link http://electro-medical.blogspot.com/

If you wish to get some details; check the site linked here. Pull up older posts.. http://electro-medical.blogspot.com/

Replacement Parts for Fitness Exercise Equipment at SPORTSMITH The following link is to the diagram for your model. Hopefully these images will assist you. http://www.sportsmith.net/images/product_support/NordicTrack/NTL290120%20-%20NORDICTRACK%20COMMERICAL%202950%20TREADMILL/NTL29012.0ed.pdf

If you wish to get some details about treadmill repair then check the following link. http://electro-medical.blogspot.com/

If you wish to get some details about treadmill repair; check the site linked here. Pull up older posts..... http://electro-medical.blogspot.com/

If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electro-medical.blogspot.com/

If you wish to get some details; check the site linked here. Pull up older posts................ http://electro-medical.blogspot.com/

If you wish to get some details about treadmill repair then check the following link http://electro-medical.blogspot.com/

can you place a blanket on the floor and tip the unit on it's side and put one end through the door followed by the rest slide it through on the blanket

first you can remove your console after you can open side post

the resistance is done by a magnet and a motor that moves it closer or farther away from the flywheel. possible the motor is bad or not adjusted properly

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electro-medical.blogspot.com/

You have to check the position switches at both upper and lower position of the incline. If the switch or sensor is faculty then the incline Motor will not stop and will go beyond the limit. of you wish to get somoe more details about treadmill repair and maintenance then check the following link. http://electro-medical.blogspot.com/

Can be the lower limit switch be faulty. Of you wish to get some details about treadmill repair and service then check the following link http://electro-medical.blogspot.com/