NordicTrack Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 13 Products
  • 239 Answers
  • 3K Views

there would be a circuit barker on the treadmill. check whether it is in off position .
If you wish to get some details; visit the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

NordicTrack... | Answered on Jan 10, 2017


The motor control board is faulty. Can be the IGBT in it. IGBT controls the voltage to the motor. If its got shorted then this problem can occur. If you are unaware of dealing with electronics then good to buy a new board rather than trying to repair the existing one.
If you wish to get some details; visit the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

NordicTrack... | Answered on Jan 07, 2017


The motor control board would be faulty.
If you wish to get some details about treadmill repair ; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

NordicTrack... | Answered on Dec 20, 2016


If you wish to get some details about treadmill repair and calibration; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

NordicTrack... | Answered on Dec 16, 2016


The magnetic read switch is faulty . You have to replace the reed switch.If you wish to get some details; check the site linked here. Pull up older posts
http://electro-medical.blogspot.com/

NordicTrack... | Answered on Nov 02, 2016


You have to check the position switches at both upper and lower position of the incline. If the switch or sensor is faculty then the incline Motor will not stop and will go beyond the limit.
of you wish to get somoe more details about treadmill repair and maintenance then check the following link.
http://electro-medical.blogspot.com/

NordicTrack... | Answered on Oct 03, 2016


There is a procedure for adjusting the treadmill belt. Almost all the treadmill follows the same procedure. If you wish to know how to adjust the treadmill belt properly then check the below added link. Even after that if you face the same problem then you have replace the running belt of your treadmill.
http://electro-medical.blogspot.com/

NordicTrack... | Answered on Oct 03, 2016


If you wish to get some details about treadmill calibration and error code troubleshooting then check the following link.
http://electro-medical.blogspot.com/

NordicTrack... | Answered on Oct 03, 2016


the motor drive assembly is seperate from all the electronics that you program and the incline motor ,although it may not work if there is a "Saftey 'Clip that attaches to the machine and clips on yourself
it wont work without this "or if this Magnetic Clip is 'Faulty,
If you can lay Machine down on its side or look for a plastic cover at the front or underneith and see if you can Unscrew and access the
motor ..there may be a Overload Reset Button or Fuse just after where the Main Power Cord goes into the Tredmill.
tred mills also are common for getting pet fur and hair in the motor which can get caught up in the Brushes, (I Think it is Most likely a Fuse or overload switch that is inline with the main Drive Motor.(if you can post exact Model# of TREDMILL I can have a look at the Electrical Diagram and make a more accurate conclusion ,Cheers!

NordicTrack... | Answered on Aug 19, 2016


Can be the lower limit switch be faulty. Of you wish to get some details about treadmill repair and service then check the following link
http://electro-medical.blogspot.com/

NordicTrack... | Answered on Aug 19, 2016


If you wish to get some details about treadmill repair then check the following link
http://electro-medical.blogspot.com/

NordicTrack... | Answered on Aug 19, 2016

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top NordicTrack Experts

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

Kardoc

Level 3 Expert

4619 Answers

Are you a NordicTrack Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...