Nordic Track Logo

Nordic Track Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 446 Products
  • 5K Answers
  • 354K Views
0helpful
1answer

Our NordicTrack T5 zi treadmill belt is not moving...

Belt Not Moving: If the belt isn't moving, there are a few potential causes. One common issue is a faulty motor controller. Even if the red LED on the control panel is lit up, it might not be sending voltage to the motor. To check the motor, follow these steps: First, test the motor using the methods outlined in this guide: Motor Testing. Motor Testing (treadmilldoctor.com) If the motor is working, the motor control board may be the culprit. Console Wire Check: Inspect the console wires that run from the motor board through the primary wire. Loose or damaged wires can cause the belt to stop moving. Reconnect any loose wires. Smoking Smell: The smoking smell you noticed could indicate an electrical issue. It's essential to address this promptly. Off-Center Belt Alignment: If the belt is off-center, it can cause problems. Confirm that the treadmill is on level ground by using a bubble level. Then, follow these steps for belt alignment: Belt Moves to One Side. How to Fix Treadmill Belt Slipping to One Side ' Stay Centered (treadmilldoctor.com) Loud Mechanical Sound: The noise during operation might be due to misalignment or worn components. Inspect the treadmill's moving parts for any signs of wear. Retirement Decision: Based on the severity of the issues and potential repair costs, you'll need to decide whether it's worth fixing or if it's time to retire the treadmill. Professional Inspection: If you're unsure, consider having a professional technician assess the treadmill.
3/31/2024 6:45:09 PM • Nordic Track... • Answered on Mar 31, 2024 • 18 views
0helpful
1answer

Nordic Track T12 si , belt won't run

If the belt on your Nordic Track T12 si treadmill is not running even though the display and other functions appear to be working, there are a few troubleshooting steps you can try:
  1. Check the safety key: Ensure that the safety key is properly inserted into the console. The treadmill will not operate if the safety key is not securely in place.
  2. Reset the treadmill: Turn off the treadmill and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on. This can help reset the treadmill's internal systems and may resolve any temporary issues.
  3. Calibrate the incline: If you recently used the incline function, it's possible that the calibration of the incline mechanism is off. Consult the user manual for instructions on how to calibrate the incline. This process may vary depending on the specific model of your treadmill.
  4. Check the motor and drive belt: Inspect the motor and drive belt for any signs of damage or wear. If the drive belt is loose or worn out, it may prevent the belt from moving properly. If necessary, consult the user manual or contact Nordic Track customer support for guidance on inspecting and adjusting the motor and drive belt.
  5. Lubricate the belt: Insufficient lubrication can cause the belt to stick or not move smoothly. Refer to the user manual for instructions on how to properly lubricate the treadmill belt. Use a silicone-based lubricant recommended by the manufacturer.
  6. Contact customer support: If none of the above steps resolve the issue, it is advisable to reach out to Nordic Track's customer support. Provide them with detailed information about the problem and any troubleshooting steps you have already taken. They will be able to offer further assistance, including potential repair options or guidance from a technician.
6/28/2023 2:41:46 AM • Nordic Track... • Answered on Jun 28, 2023 • 158 views
0helpful
1answer

Why is NordicTrack C900 belt lifted at the edges? How to flatten belt edges even if it's already properly tightened, centered, and lubed?

Question edited for clarity and typos. Question moved from Televisions Category, to make model. It is either that the belt is too tight, or the belt is worn out. The rollers are slightly 'crowned' fatter in the centre than the edges. If the belt is too tight, it will pull the edges up, or it is has been run too long or too tight, the belt wears in the centre, so being thinner in the centre, it curls. Time for a new belt. Posting pictures is easy. :>D
3/4/2023 7:39:22 PM • Nordic Track... • Answered on Mar 04, 2023 • 82 views
0helpful
1answer

Nordictrack Audiorider R400 Exercise Bike. Where do I plug in the power adapter please?

Question edited for a lot more clarity. Question moved from 'Power Computers' to a better category. The manual is dreadfully vague Note: The Console (4) can be operated with an optional power supply instead of batteries. To purchase a power supply, call the toll-free telephone number on the front cover of this manual. Plug one end of the power supply into the jack at the front of the exercise cycle. Plug the other end of the power supply into an appropriate outlet that is properly installed in accordance with all local codes and ordinances. Look on both sides of the console and also at the front of the bike itself. I have to say though, if the console didn't work with batteries, it is unlikely to work with a power supply. It is broken and that is why it didn't work with batteries. What you could do is follow the wiring harness as shown in the parts manual from the console down and where it branches off to.. Aha, I found this Exercise Equipment Technician: treadmilltech It should plug in at the bottom of the front where the 2 side shields come together or it will go into the console itself in the back. https://www.sportsmith.net/images/product_support%5CNordicTrack%5C216731%20-%20NORDICTRACK%20AUDIORIDER%20R400%20EXERCISE%20BIKE%5CNTEX4196.1-247436.pdf https://www.google.com/search?q=nordictrack+audiorider+r400+mains+adapter+operation ..
2/23/2023 2:29:11 AM • Nordic Track... • Answered on Feb 23, 2023 • 85 views
0helpful
1answer

My belt is not laying flat on the treadmill, and

They are only adjusted left to right so they run centrally. https://www.google.com/search?q=adjust+treadmill+belt ..
12/28/2022 5:48:44 PM • Nordic Track... • Answered on Dec 28, 2022 • 3,363 views
0helpful
1answer

Nordic Track C1550 Treadmill. Had to remove console to move the treadmill now the numbers for speed and incline on the sides of the console don't work.

https://www.livestrong.com/article/410922-the-controls-are-not-working-on-a-nordictrack-treadmill/
12/11/2022 5:53:36 PM • Nordic Track... • Answered on Dec 11, 2022 • 112 views
0helpful
1answer

Nordic Track S15i studio cycle. Reset wouldn't work using the pinhole reset button. Screen keeps shutting off and on.

Question edited for clarity and correct name of maker. Question moved from Tablets to maker category. Contact Nordic Track with a view to returning it under warranty, or out of warranty repair. https://www.google.com/search?q=Nordic+Track ..
11/9/2022 5:56:31 PM • Nordic Track... • Answered on Nov 09, 2022 • 91 views
0helpful
1answer

The controller led bllinks for

If the blink pattern is four blinks followed by a pause and another set of four blinks, then the controller has detected a bad switch, turn the machine off and back on. If the problem persists the controller board will need to be replaced.
10/6/2022 4:59:39 PM • Nordic Track... • Answered on Oct 06, 2022 • 802 views
0helpful
2answers

I have nordictrack A2105 and although we "oiled" the belt and replaced motor belt, it still slips. What are we doing wrong?

If we use the treadmill daily it might need maintenance regularly. Running of 180 hours on the treadmill might lose the belt. Drive belts usually last for longer time of 5 to 7 years.So you have to adjust the tension of the belt. Keep enough tension in the drive belt If a user wants to improve the motor efficiency it is necessary to connect the motor to the front wheel which helps the belt to spin. Too little tension results in slippage, excess heat and high-pitched noise, or too tight belt produces tension causing stress on belts, bearings, and shafts. Prevent premature motor failure by adjusting the belt at a suitable place. The belt should be fixed half an inch of play. To improve the efficiency of the motor align the belt properly and lubricate it on time. Keep in mind such useful options may help the user. When the belt slips off the track, the friction between the belt and drive pulleys causes the belt to overheat. If you hear a high-pitched noise, it's time to replace the belt with a new one. How to Ascertain that the drive belt can still be used? If you test Front-wheel by walking on the treadmill and the belt stops but the motor is still moving, It means that the drive belt is loose and needed to be tightened or replaced. Keep in mind There are some exercises that are not suitable for the treadmill like jumping on it. This kind of usage can be rough on your treadmill and lead to your treadmill belt slipping.adust the ten-min-no3sozbgmwgshwiqout0lfe4-d-2.jpg
8/20/2022 2:35:44 AM • Nordic Track... • Answered on Aug 20, 2022 • 725 views
0helpful
2answers

Nordic. Track incline won't work or calibrate

I have a NordicTrack C2155. Incline not working. There is a schematic inside. There are red, white, & black wires from the circuit board to the incline motor. Unplug the treadmill and have a licensed electrician construct a flying lead cord with a male spade on neutral and female spade plug on hot. Connect neutral to white and hot to where either red or black were connected. Plug in to see if the motor runs. Careful to remove power when the incline reaches its limit and reverse direction. If the motor runs in both directions, the motor is good. Follow the black two conductor wire to the circuit board and unplug from board. Check continuity across this switch. Run motor and this should toggle off and on. If all this checks out then the problem must be with the circuit board. On my treadmill, the schematic says that +5v should supply the sensor, but I only get +3.3v, which is TTL level. The drive motor sensor supply is +5v. The incline motor doesn't even show a sign of trying to run. Either the output transistor is burnt out or the low voltage caused an error so that it does not try to run the motor. Either way, I'm quite certain that a new controller board will remedy the problem.
8/3/2022 11:36:19 PM • Nordic Track... • Answered on Aug 03, 2022 • 19,294 views
0helpful
1answer

I need the wiring diagaram for Nordictrack Treadmill C2300 model #12905.5

Contact Nordic Track directly to inquire about a diagram.
3/29/2022 11:02:40 PM • Nordic Track... • Answered on Mar 29, 2022 • 181 views
0helpful
1answer
0helpful
2answers

My Nordictrack treadmill seems to

it is trying to calibrate itself, let it go the whole way up and then down without interrupting it. Then it should be fine.
2/14/2022 12:45:11 AM • Nordic Track... • Answered on Feb 14, 2022 • 893 views
0helpful
2answers

Nordic Track Audio Slider 990 NTEL7906 . 3 elliptical Extremely hard to pedal after changing belt.

ODD AS IT MIGHT BE WE LEARN TO TAKE PICTURES BEFORE REMOVING THINGS .
2/8/2022 5:49:32 AM • Nordic Track... • Answered on Feb 08, 2022 • 193 views
0helpful
1answer

Show motor brush cover on nordic

THE PLASTIC COVER WHERE THE SMALL BRUSH OF THE TREADMIL NORDICTRACK L-355197 MOTOR GOES BROKE. WHERE CAN I GET THIS COVER?
1/22/2022 7:52:57 PM • Nordic Track... • Answered on Jan 22, 2022 • 376 views
0helpful
2answers

Nordictrack C2050 treadmill console not responding

https://www.audiusa.com/content/dam/audiusa/brochures/2019/2019_Audi_Q7_QSG.pdf
1/13/2022 4:42:01 AM • Nordic Track... • Answered on Jan 13, 2022 • 2,485 views
0helpful
1answer

NordicTrack treadmill EXP 1000

Please note that these instructions don't apply to all models of treadmills. Many recent models, including all models with touchscreen consoles, do not have the capability for the user to calibrate the speed. Speed calibration is a process that is used to correct imbalances in the machine's operating speed. Please note that this procedure involves pushing the machine to its maximum speed very quickly. Do NOT stand on the treadmill while performing this procedure. First, you need to enter calibration mode on the console. To do this, press and hold the STOP and SPEED INCREASE buttons (this will be either an up arrow or a + (plus) symbol). While holding these buttons, insert the safety key onto the console. This will cause the machine to go into calibration mode. After this has occurred, you may let go of the buttons and the safety key. Next, press the stop button once. This will enter advance the screen to the next feature of calibration mode. As said previously, do not stand on the treadmill while performing this procedure. Press and hold the speed increase button. Watch the console. You will see a number on the display that will increase as you hold the speed increase button. Continue to hold the speed increase button until the number changes to "85." This will take the treadmill to its maximum speed, which will also be displayed on the console. Please note that the example below only demonstrates the console displaying "85", not the treadmill's operating speed.
11/5/2021 11:40:28 AM • Nordic Track... • Answered on Nov 05, 2021 • 175 views
0helpful
1answer

Nordic Track Elite 7700 has no power, Why?

See this video:- https://www.youtube.com/watch?v=Bu_SEUU2umo
10/23/2021 4:40:59 PM • Nordic Track... • Answered on Oct 23, 2021 • 234 views
0helpful
1answer

My nordicTrack is saying checksum failed

Mi caminadora nordictrac apex c500 marca el error checksum: fail, alguien sabe como arreglarlo?
10/4/2021 7:32:00 PM • Nordic Track... • Answered on Oct 04, 2021 • 599 views
Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Nordic Track Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

vince

Level 3 Expert

2530 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66827 Answers

Are you a Nordic Track Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...