New Bright Toys - Answered Questions & Fixed Issues

Make sure the batteries are installed correctly and that the connection points are clean and have a tight connection.

Here are a couple of resources from New Bright:
http://www.newbright.com/public/electric-train-faq

http://www.newbright.com/images/Manuals/384%20ws%20manual.pdf

There is no On/Off switch on the train. Power goes from wall plug to transformer, then from transformer to track clip, which must be attached to the track. A control line goes from the track clip to the controller. Mine has a green light just above the red On/Off button that will come on even if the engine and tender are not on the track. The tender does all the work, and must be connected to the engine and on the track. There are four sliding contacts between the tender wheels that provide contact with the track.

Yes it should. See the adverts and repair videos in the link. https://www.google.com/search?q=Does+a+New+Bright+Christmas+Express+1996+engine+smoke ..

Sold on eBay but looks like the bands at missing. Go to Home Depot and buy some -O-rings that fit. 3 or 4 each side should do it. https://www.ebay.com/itm/185618976768 I wonder if these would fit? Ask the internal diameter. https://www.amazon.com/Plarail-Repair-Parts-Rubber-16pcs/dp/B000LXS8IM ....

Might try contacting manufacturer for this vintage item, or contact sellers on eBay to ask to purchase copy of instructions. http://www.newbright.com/support/battery-powered-train-faq/ Example on ebay: https://www.ebay.com/itm/1997-Complete-Mint-Condition-Service-Express-Railway-Radio-Control-G-Train-Set/372854424459?_trkparms=aid%3D555018%26algo%3DPL.SIM%26ao%3D2%26asc%3D20160908110712%26meid%3Dfd6b8137f24247c0ac8811d494b2c37d%26pid%3D100677%26rk%3D3%26rkt%3D30%26sd%3D274112638776%26itm%3D372854424459%26pmt%3D1%26noa%3D0%26pg%3D2386202&_trksid=p2386202.c100677.m4598

Your best best is going to E-Bay.

What size batteries does the 1986 D and W R.R Denver express take

The controller and the car must be matched. Sounds like both are matched using the same frequency. Look at the instructions for changing the controller and car to a different frequency Then change one car and controller. try here Technical Documentation New Bright Industrial Co for info

check the electrical current to the trans former , then check the out put from transformer, may not be getting adequate electricity flow to operate , and if you continue to operate under required current , it may damage engine and or transformer , gd luck

there is no resistance in a fuse it is designed to blow when a short circuit happens after the fuse to protect the circuit fix the problem first

We have no parts for sale here at this website.

Tomoct

depends what the railway is representing. It matters, for example, whether you are in the US or Europe. I recommend that you contact the company to get an unambiguous answer Contact New Bright Further reading on G-gauge can be found here scale Wikipedia the free encyclopedia from which you will understand why it is not straight forward to answer your question with information available. In the US, the article says, " 'Gauge One' scaled at 1:32 (3/8" to the foot) used to model standard gauge trains of 4 ft 8 1?2 in (1,435 mm) standard gauge gauge." hope this helps (a bit)

Go to newbright.com . They have a technical support , or contact prompt. I'm sure they can help., or try [email protected]

From amazon for sure, click here and take a look: Amazon com Remote Control Toyota FJ Cruiser. I hope this was helpful. Cheers

Not sure what instructions you need, but the setup is very simple.
1. Put your track together
2. Attach the track power connector by slipping it under the track and pushing, then lift up the other side. This will make the two metal contacts connect to the track.
3. Plug the connector from the power pack into the track module (It should only go one way)
4. Plug the control box (looks like a telephone cord) into the track module, Will only go one way
5. Place the locomotive on the track.
6. Place the Treetop Tender on the track (you need both to make it run)
7. Connect the large connector from the treetop tender to the loco
8. Turn on the command module and press forward ...

You should now be running in circles ...

Hope this helps...

Check the power circuit that goes to the track if there is an open circuit, open circuit means, break or cut line that can not flow the current going to the track to give a power to the train, ok.

http://newbright.com/wp-content/uploads/2014/06/6689-ws-Manual.pdf

That took me about 10 seconds to find online: http://www.radioshack.com/graphics/uc/rsk/Support/ProductManuals/6000966_PM_EN.pdf

check the battery positioning and the switch.