Netopia Popular Questions, Answers, Tips & Manuals

Base from the description of your problem it seems that the issue here is not with your Netopia wireless adapter but with your 2wire wireless router, because the 2wire is the one responsible to broadcast the wireless signal so your Netopia can pick it up.

So what you can do here is to reset the 2wire router by pressing the reset button of it its a small hole there , then you will need to reconfigure that and it will be better if you do that with the ATT people so they can tell you how to reconfigure the router.

Hello
Check with your router manufacture on how to log in to the router.

Once you have logged in,check that upnp or universal plug and play is checked to on.
This should allow x box to work through the router.

call your isp

try here GENERAL ROUTERS RESETING

well, if you have been blocked by the admins of the website , u can still get an access to the website, as what the admins do is , they block ur IP, and hence u cant access it, if you want to get the access, then, change your IP address. to know How to change, it , u can mail me @ [email protected] i can't publish it online. good luck

Try this GENERAL ROUTERS RESETING

default STC password for Echolife HG532b a.k.a. Afaq shamel 007 :address: 192.168.1.1 username: Afaq_Shamel password: Stccpe_2009

Four ethernet ports are standard on all wireless gateways. Yes, it can provide you wireless connection.

If you mean the reset button has been pushed and now the modem needs re-programing, then the modem has defaulted to its factory setting. Its IP address is now 192.168.1.254, its user name is Admin, and its password is the same as the serial number of the modem, usually found on the label on the bottom of the unit.

It should be a wireless adapter that you plug into a USB port. It's only needed if your computer doesn't have built-in wireless capabilities. If you plug it in and your system asks for a driver it should be on the CD that came with the unit.

this device may not work in the 64 bit mode because it is a 32 bit device and the driver may not be available for it in the 64 bit mode. The manufacturer is the place to get the up dated drivers.
I suggest using the device in the Windows Vista or XP mode and the drivers should work for this device.

You need to set up port forwarding for the ports you're planing on using.

This is an older unit and drivers are not available for any OS beyond XP service pack 1. You can try to use the XP drivers in windows 7, but this is not recommended as they may not work, and you may experience other problems such as crashes and system instability.

It took some digging, but the software can be downloaded from Motorola's website:
http://broadband.custhelp.com/app/answers/detail/a_id/21282

They have drivers for Windows 98SE, Me, 2000, XP, Vista, and 7.

Here is the link from where u can download the driver.
http://www.belkin.com/support
click on the s/w update and you will get it in case that also don't work then kindly look down the page.

if you have the manual with the unit locate where is the reset button then push it for 10 sec.

Try to access your router's gui. To do this, you have to use your internet explorer.
1. Get your default gateway address first. a. press the windows key + R b. type cmd then press ok c. on the black screen type ipconfig then press enter d. look for the default gateway address 2. Type the default gateway address on the internet explorer address bar and you will be able to see your router's gui
3. Refer to the manual posted on the link below. Refer to Chapter 7 to get the WEP key of your router.
note: you need to connect wired to your router before anything else.
Netopia Wireless Router Manual

You can also configure it with below method.
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then click on WAN settings set it as your internet service provider settings enable DHCP Then click on wireless and enable it. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Welcome to FixYa!
Hi!

• Yes, you'll need a to install the driver for Netopia. You need a software to install it and to make it work. Here is a link on where you can download the driver :

http://fastaccess.drivers.bellsouth.net/archive.html#cayman

• If this was given to you together with a self-install cd just use that. Its easier.

Hope my answer helps. Thank you for using FixYa! Have a nice day.

that is wifi adapter, that can receive the wireless lan connection