Netopia Popular Questions, Answers, Tips & Manuals

I presume that you mean "from a web site" that the web site is hosted somewhere out on the greater internet.... The problem that you are encountering is probably related to NAT (Network address translation). The "In" side of a router, is typically a "private network" there are pre-assigned number groups for these - a common one is in the 192.168.x.x range. Problem is that the "outside" of your Netopia router will be dependent on your ISP< and unless you are paying them extra for a static IP address, is likely to change every time you reboot - or sometimes they bump them every 24 hours. So, first thing is get a dynamic DNS Entry - www.dyndns.org is one supplier - I think you can get one address for free from them, pay for more.. YOu set up something like CMVideo.dynsdns.org on their site, and set up dyndns support in the netopia router... Then you want to open the specific port on your router, to go to the internal IP Address of your camera. (YOu mention Multiple Cameras - depends on the Camera you may have to go for multiple dyndns (one for each...) ).I am a little confused/concerned about the second router "tier" - if you have the Belkin configure as an Access Point only, all good, if you are trying to run it as a router behind a router, it will probably never work - double nat-ting" is a no no with most consumer Routers. Simple solution is to tap from Netopia lan side to Belkin Lan side (rather than Belkin Wan Side)

router admin password can be different from wireless password. this page should help:http://portforward.com/default_username_password/Netopia.htm good luck

This one?http://www.netwood.net/support/manuals/Netopia-3347W-ENT_qsg.pdf

see the user manual of your product

Try connecting to another USB port and if that does not help try reinstalling the latest driver and if that does not help then your device needs to be replaced.

You need to contact your local phone company or DSL reseller. Netopia makes the modem/router, but doesn't offer service. Note that your service provider may or may not support this particular model of equipment on their network. You're probably better off shopping for the service first and then shopping for the modem/router to use on it. The equipment is realatively inexpensive, while the service is not.

Wireless routers don't need drivers. Maybe your wireless adapter needs drivers.

MAKE AN ACCOUNT HERE ARRIS THEN LOOK FOR THE FIRMWARE.

Try recycling the power, unplug it for 30 seconds then plug it back in and let it reboot. Try Netflix again.

Using a router is a great way to create a home or office network without having to spend a lot of money. As long as you have a broadband Internet connection through an Internet service provider, you can use a router to get all of the computers in your home or office connected. If you have chosen Netopia as your router brand of choice, you will have to configure it to make your network operable. Power on your Netopia router, broadband modem and computer. Open your Internet browser. Type the router IP address, 192.168.1.254, into the address bar. Hit "Enter" on your keyboard. Log into your Netopia router with the username and password assigned to you by your Internet service provider. Select "Expert Mode." After entering expert mode, you will see a menu bar at the top of the configuration window. Click on the "Home" tab. Many Internet service providers will ship your Netopia router to you preconfigured. If it is preconfigured all of the fields, such as IP address, subnet mask and default gateway will already be populated. If the fields are not populated, proceed to the next step. Click on the "Configure" tab. Select "WAN." Select "ATM." Enter the "VPI" and "VCI" numbers provided by your Internet service provider. Choose your encapsulation option. For example, "Routed IP," "PPPOE," etc... Click "Submit." Select "WAN" on the left side of your configuration window. Choose the "VCC1" option. Select the option to "Enable Interface." If you do not have your own IP address, choose the option to "Obtain an IP Address Automatically." If you do have your own IP address, uncheck the automatic IP address box. Type in your IP address if you have your own. Enter your subnet mask. This information can be obtained from your Internet service provider. Select the "NAT" option if you are using your own private IP address for your network connection. Click on "Submit." Select "WAN" on the left side of your configuration window. Ensure that there is a check in the "Gateway Option" box and "IP Address" is selected as the "Interface Type." Type in your "Default Gateway" address. This can be obtained from your Internet service provider. Click "Submit." Select the "Configure" tab at the top of your window. Select "LAN." Select "Enable Interface." Type in the IP address for your router and subnet mask. Click "Submit." Click on the yellow caution symbol on the top right hand side of your window to save all configuration changes. Click on "Save." Restart your computer for the changes to become effective. http://www.netopia.com/support/hardware/technotes/CQG_121.html

GO TO THIS LINK

default STC password for Echolife HG532b a.k.a. Afaq shamel 007 :address: 192.168.1.1 username: Afaq_Shamel password: Stccpe_2009for Echolife HG532b

here's the link I found that the Ralink RT73 driver seems to work with the Netopia TER/GUSB-N1. I found a form about how to install on a MAC maybe it will be helpful to you

Reset the router here is how

CALL YOUR ISP FIRST. wi-Fi Protected Setup (WPS) is a standard for easy and secure wireless network set up and connections. Some of NETGEAR's products use the name Push 'n' Connect for WPS. To use WPS, your product must support WPS and be compatible with WPA security. WPS can automatically set up a random network name (SSID) and strong WPA wireless security for wireless routers, access points, computers, adapters, Wi-Fi phones, and other electronic devices. WPS lets you use a push button or enter a personal identification number (PIN) instead of manually entering a network name (SSID) and password:

• Push button. The WPS button is either on the product or a clickable button on a wizard or utility screen.

First turn off the firewall and then install it.....Open Windows Firewall by clicking the Start button->click Control Panel->click Security->click Windows Firewall.Click Turn Windows Firewall on or off. Administrator permission required If you are prompted for an administrator password or confirmation, type the password or provide confirmation. Click Off (not recommended), and then click OK.**If you need any kind of technical assistance you can contact support cell at http://www.vtechsquad.com/

Use portfoward dot com if setting up a game, but use the free instructions by hardware and game.

This will explain, doesn't your ISP provide different plans? http://www.pcworld.com/article/158552/check_ISP_speeds.html

YES

CALL YOUR ISP