NetGear Computers & Internet - Page 4 - Recent Questions, Troubleshooting & Support
Facing the Netgear router connectivity Issue?
There are lots of reasons to facing No internet issues.
Follow below steps to fix issue-
- Check cable connection are not loose, or damage.
- Make sure your firmware is updated
- Soft reset
- Hard reset
2/7/2019 11:22:35 AM •
NetGear...
•
Answered
on Feb 07, 2019
I have a digiland dl 9002 (bk32) the wrong password to netgear 74 router was entered how do you change password to correct?
there might be a setting in the digiland dl 9002 to forget wi fi connection in the wi fi list of possible wi fi networks.
or reset the unit
they apparently have a small hole that you put a paper clip into and push hidden button to reset the tablets settings to factory default.
With tablet back camera facing you there should be a hole at left bottom corner of back of tablet .
Press and hold this in with the paper clip or a tooth pick
unit should power down
then press power button to power back up
it should be reset to factory defaults
1/8/2019 11:12:57 AM •
NetGear...
•
Answered
on Jan 08, 2019
Netgear DHCP issue
It sounds like it's not configured to be a DHCP server. It should be a setting you can turn on. Login to the router. You may need to manually set your computer's IP to be in the same subnet as the router so that you can do so. The default address for the Netgear 7550 would be
http://192.168.254.254, so you'll have to set your computer's IP to something like 192.168.254.253, and then browse to the above address. Username and password are both "admin". If that IP doesn't work, try setting your computer's IP to 192.168.1.2, and browse to http://192.168.1.1, then look for a "DHCP Server" setting in the Local Area Network section, and make sure it's checked.
1/6/2019 12:03:42 PM •
NetGear...
•
Answered
on Jan 06, 2019
Cannot login to router
I'm not sure what you tried, but I'll run through the things I'd do, and hopefully there's one you haven't tried yet.
First, you should be connected with a physical cable and not trying to login wirelessly.
If you've done a factory reset, and you can get to the login page, but it just won't log in, but it's not complaining about the password being incorrect, it could be an issue with the browser. For example, it may be trying to run a Java app and the settings in the browser are disabling it. You can either look into that, or I've found that Netgear offers free application called "Netgear Genie" which you can download from their website, which allows you to do all the same things to service your router, but it's done from an actual program that runs on your computer, instead of running inside a browser. I had a netgear router that wouldn't communicate at all via the browser, and I was able to get in using this program.
Wont connect to internet
You need to reset the router if the lights are flashing. Press the reset button at the back of the router for about 20 seconds then release it. Now unplug the power for 20 mins as well and plug it back in. Make sure your connection is right. PC connected to port 1 and modem to WAN or Internet port.
I have a router Netgear
Try RESETTING the router.
To RESET the Netgear, power up the Netgear then press andhold the RESET button at the back of the router until all the LEDs flash.
Connect a LAN cable from the Netgear to the LAN port on yourcomputer, open a browser and enter the Netgear configuration URL -
http://192.168.0.1
The default login = admin
The default PW = password
You can now change the admin password and configure thewireless settings.
Go to the wireless configuration and set up the SSID and WPA or WPA2encryption.
Apply these settings to the wireless card in your laptop/computer.
To secure your wireless network from unauthorized access, please click on thislink and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security
I am trying to install a netgear cg814wg wireless
You can try resetting your netgear router to default settings. the reset is button located on the rear panel of your gateway to reset all settings to their factory defaults.
Here's the router default configurations settings:
User login URL: http://192.168.1.1
User name (case sensitive): admin or superuser
Login Password (case sensitive): password
You can also check and download your router manual & user guides here:
http://documentation.netgear.com/cg814wgv3/enu/202-10297-01/pdfs/FullManual.pdf
Good luck,
Ryan
I cannot access the netgear settings.
to access the router you will need to open up your web browser and type in 192.168.0.1,it will then ask you for a user name and password ,the user name is admin,the password is password,that will get into the netgear utility for the router,that info can also be found on the bottom of router,if that doesnt work then you will have to reset the router to the default settings by holding in the reset button for about ten seconds located on the back ,you will have to use something that is small enough to depress it,you have to reset it while it is on,if you got it used then you should reset it anyway so that you can configure it according to your situation,ok have fun and good luck,you can get detailed info from netgears website.
Not finding what you are looking for?