My nav 2100 was on then just went off,now it wont
Hello,
The first thing to check is the power adapter output. It may be plugged in but still not putting out any voltage. Use a multimeter set to DC volts and check for a reading of 5volts. Another thing to try is take the unit inside by your computer and use the sync cable that came with it to connect to the PC, this cable will also charge the unit. If the charge light comes on then try powering it up after a few minutes. If both of these don't solve the problem then the next thing to check is the power plug in the GPS unit. You will need to pop the back of of the unit and make sure it is still soldered to the board, if not then you will have to resolder it or get someone to repair it for you. If you need it serviced for this type of problem we offer a repair service for your unit.
Contact us at:
[email protected] if you have questions
I hope this helps you, if so please rate our solution.
Buddy
Corporate Computer
www.ccl-la.com
1/21/2017 2:48:09 AM •
Navigon 2100...
•
Answered
on Jan 21, 2017
•
444 views
HOW I FIX THE MESSAGE I GET WHEN I HIT NAVIGATE - ROUTE CALCULATION FAILED
Doy you get that message always, or only when you are inside a building or close to very tall buildings?
Make sure your device has a clear view to open sky, so it can find enough satellites, to calculate where it is. And if this happens, give the device enough time to find out. It could take up to one or 2 minutes before it is ready.
Where can I get Map update for Navigon 7100?
From what I've been reading, Navigon is pulling, or has pulled out of the US. They claim to still support map updates if you purchased a subscription but to spend $ on it now would be risky in my opinion
Navigon 23 reset
1. Use a thin object to press the reset button located on the right
side of the device. The device will be switched off.
2. Press the power button for at least 10 seconds to switch the
device back on.
2/26/2014 8:14:57 PM •
Navigon GPS
•
Answered
on Feb 26, 2014
•
141 views
Haveing trouble selecting first and second gears when engine cold
hope you not using sat nave to try and select a gear you will have trouble..... any way check that you have oil in the gear box and dont have a leak. if you have a leak then you dont have enough oil in the box. if all fine and no leaks check the level of oil and add some if low. also grease up the gear changer shaft at both ends. check for rubber seal damage. if all ok just grease them. wile you under the car have some one move the gear stick from first to second with out the engine moving checking that the alignment of the gear change shaft . making sure the shaft lok dose not move with the a gap. if so check it or change the part.
Navigon easy 40 no sound
The usual problem is the voice volume is turned down. This can happen when you are adjusting the volume down just as turn by turn instructions are starting; thus you don't notice it happened, or someone else did it or software glitch caused it or Murphy's law.The way to fix it is turn vol up to max and set navigation and start driving. As you get to navigation points where you would expect the turn by turn instructions hit the up volume button. Keep trying it will only go up whilst instructions are being broadcast. Try using repeat last directions function to get a better shot at it.This happened to me and this was the fix, odd but true. Also see if there is a turn by turn vol level in settings.Hope it works for you.
GPS
Gprs is most beautiful internet concretion.
On-site training also
allows a business to schedule training around workflow, eliminating the risk
that professionals will leave for training during a busy period of the day or
crunch time on a project. This avoids costly downtime and makes workflow as
efficient as possible while still ensuring employees receive the education they
need.
10/6/2012 8:44:51 AM •
Navigon 2100...
•
Answered
on Oct 06, 2012
•
189 views
Not finding what you are looking for?