Motorola Mobility Televison & Video - Page 2 - Popular Questions, Answers, Tips & Manuals

if the box has a manual button for vol up press it and you should see it display on the TV set itself.

motorola universal

Try this link to download the manual. It has all details.

Mitsui 0067 0586 0517 0039 0265 0041 0385 0102 0066 0247 0324 0401 0463 0473 0393 0609 0485 0193 0379 0546 0065 0238 0075 0225 0221 0365 0574 0744 1067.

No. There is no setup code for Charter Cable, with this Motorola remote control

go to www. fitness.manualsonline.com or www.remotecodelist.comGod bless you

0023, 0024, 0043, 0044, 0045
Si ninguno funciona, puedes usar la función para buscar códigos del control, para esto hay que: 1.Con el televisor encencido, mantener presionado el botón de TV por al menos 6 segundos hasta que se enciendan las luces de cada dispositivo y la luz de TV permanezca encendida. 2.Presionar POWER, la luz de TV parpadeará 3 veces y se apagará. 3.Presionar la flecha hacia arriba hasta que el televisor se apague, una vez que se apague hay que presionar OK. Al presionar OK, el control guardará el código y ahora podrá controlar el televisor.

You haven't told us what is the model of the remote you are now using it so we can't know what are its stored set of controls and if the one for the new box are between them. But there is another possibility: a so called learning remote - a remote that can learn the commands from an original remote. So if your present remote is a learning one - almost surely is, since there are no universal remotes designed with codes for door opening or thermostat changing - then all the persons helping you will have to do is to program the new remote's commands in it the way they programmed the other unusual commands, so no need for a preprogrammed set and its 3-digit entry code.

you would need a "doggle" to switch from stereo (the red and white near the yellow on the back) to headphone. i have seen the sort of thing at best buy and radio shack. good luck

Here is a link to motorola for the manual/spec sheet for you remote
http://www.motorola.com/staticfiles/Consumers/Products/Home%20Digital%20Video/DRC800/_Documents/Static%20Files/DRC800-User-Guide-US-EN.pdf

you should find the codes on this document or instructions on how to set it up manually

Hello,

Be patient for a while or a little longer if you have been waiting. The channel will certainly come back.

There might be some signal problem from your network provider. Or call the customer service of your network provider and they will resolve the problem.

Give the code shown on the receiver to our network provider and it will be used to rectify the problem.

Good luck.

Hi, My name is Tina and I am with Suddenlink. Are you still having this issue? If so, please feel free to email me at tina-AT-suddenlink-DOT-com for resolution.

same problem here. stb turns off randomly and displays 8888 and locks itself. usually if your press the select button 4 times and turn the stb on again it works but you will have to wait 20 min for it to get the channels or dvr. still no permanent solution though

try it but try to look for a reset button in the unit or if you have the manual try to look for default setting.

i had a similar problem with an IR system once. thats the thing that makes it so you can hide the box in a closet so you dont have to see it. it was the ir that was the problem and ABT replaced it. try to find out if the box or the remote causes it. maybe a down button is stuck in on one or the other. if you put away the remote and use the buttons on the front of the box does it still happen? good luck

if there isnt any screws visible chances are its a barrage of flimsy clips that are fairly tricky to get apart ????battery contacts your after????if so i prefer a clean pencil eraser hope this helps

Poor signal. Check connections at all Coaxial connectors. Should be tightened. Unplug a/c from rear of DVR for 30 seconds. Allow time for DVR to reboot and update. Try again. If not resolved, call tech support for your cable company. May have to boost your signal.

DUI is actually trying to display DVI on the box (the LED won't display the V and makes it a U). You typically see this error when your connected to your TV through an HDMI cable and the handshake for HDPC is lost. The box thinks your TV doesn't support it and wants you to change your connection. The error should go away once it finds that handshake. If you were using a different input on your TV, maybe a composite or something for a DVD, and then switch back it can get lost. If it doesn't clear right away try shutting everything off and turning it back on by turning on the TV first and then the box.

Hi chestmcn. Here's how you reset your device to its defaults:

1. Make sure your receiver is plugged in, that it's connected to your TV, and that your TV is turned on.

2. Turn your receiver OFF, then press MENU on the front panel of the box. You will then see a menu on your TV.

3. Using either the up/down buttons on your remote control or the up/down buttons on the front of your receiver to navigate. Use the right arrow button to view the options for each setting.

4. Arrow down to the setting labeled "Restore All Defaults", then press the right arrow button to select that option.

5. Exit the menu and save your changes by pressing the POWER or MENU button.

For what it's worth, this issue may also be related to Comcast reference code error s0900, which means a disruption in service, usually temporary.

In case you run into more trouble with your receiver, here is a link to the user guide- http://www.motorola.com/staticfiles/Business/Products/TV%20Video%20Distribution/Set-tops/QAM%20Set-tops/All%20Digital%20QAM%20Set-tops/DCH3416/_Documents/Static%20Files/DCH3416_User_Guide_537529-001-c.pdf

I hope this helps. Thanks for using FixYa!

The clock should set automatically, synchronized with your cable provider's time. You can't change it, as far as I know. OR does it display the channel number and you want it to display the time? If so, go to your onscreen menu (home), choose setup, choose cable box setup, front LED display: current channel ----> current time.