Remove the battery, slip a small screw driver into the slot at the bottom of the radio between the outer housing and the battery tray, gently pry up. If your radio has a pair of battery contacts on the exterior they will come up with the tray. Be gentle, and do not disturb the Mylar ribbon that runs down the back of the tray. Once the tray is removed, using a frame removal tool (shaped like a squared letter U) you slip the tool in the channels on either side of the radio where you removed the battery tray. Then slide the tool upward until it meets the two plastic ears. The tool will slip under the ears and using your tool you can push the component board out the top of the housing. If your radio has an 8-dip-switch private line board, you may want to watch you do not damage or dislodge it in the process.
Are you paying for a monthly contract for the phone? First contact the store you got it from or the network provider as it might be under some sort of warranty. If it isn't you will need to take it to a good phone repairer. Almost all modern mobile phones are built as a 'sealed unit' and often cannot be repaired so you might have to consider buying a new phone.
what is a moto?what is a G9car,boat , motorcycle or what? moved yahwhat is an ACCU?a telephone, cell phone, the battery died/?well post too cell phones not cars OK?moto = Motorola?wowat random I find this at youtubelearn to use youtube any CELL works. or wreck the phone you will.some are crazy hard to do.took me 10seconds labor (googling) for you.https://youtu.be/PNM50W-wf9A
I believe for the FR60 walkie-talkies, if they are not sending or receiving, the issue could be related to the antenna, battery, or internal components. You can try replacing the batteries and/or antennas to see if that resolves the issue.
As for the T5820 walkie-talkie, if the rubber on the antenna is broken, it's likely that the antenna itself is also damaged. In this case, you can try replacing the antenna with a new one. Antennas are typically available for purchase online or at electronics stores.
In terms of cost, repairing older walkie-talkies like these may not always be cost-effective. If the repairs are extensive or require replacement of major components, it may be more practical to purchase new walkie-talkies instead.
Below are options of the options of walkie-talkies you can buy;
Hi Sherry,To disable the voicemail on your Motorola CD4 landline, you will need to contact your landline service provider and request that they disable the voicemail feature on your account.The process of disabling voicemail may vary depending on the service provider, but typically, you can do this by calling their customer service hotline or by logging in to your account online.Once you are connected with a customer service representative, explain that you want to disable the voicemail feature on your account. They may ask for verification of your account information and may need to make changes on their end to complete the process.It's also worth noting that disabling voicemail means that the callers will no longer be able to leave you a message when you are unavailable. So, make sure you consider this before making a final decision to disable voicemail.
It is possible to have the battery in your Motorola H730 headset replaced, but it would likely need to be done by a third-party repair service as the battery is not typically user-replaceable.
Motorola does not offer an official repair service for the H730 headset, so you may need to find a third-party repair service that specializes in repairing Bluetooth headsets. Be aware that third-party repairs may void any remaining warranty on the device.
You can also consider purchasing a new headset if you prefer not to have it repaired.
If your MC3300 scanner is frozen on a white background with a blue Motorola symbol and says MC33X series, you can try a soft reset to see if that resolves the issue. To do this, follow these steps:
Hold down the power button until the scanner turns off.
Wait a few seconds, then press the power button again to turn the scanner back on.
If the scanner is still frozen after attempting a soft reset, you may need to perform a factory reset. Please note that performing a factory reset will erase all data on the device and return it to its default settings. To perform a factory reset on the MC3300 scanner, follow these steps:
Press and hold the power button and the volume down button simultaneously.
Keep holding both buttons until the scanner vibrates and the Motorola logo appears.
Release both buttons.
Use the volume buttons to navigate to the "Factory Reset" option, and then press the power button to select it.
Confirm that you want to perform a factory reset by selecting "Yes" using the volume buttons and pressing the power button to confirm.
Wait for the scanner to reset and restart. This may take a few minutes.
If a factory reset does not resolve the issue, you may need to contact Motorola's customer support for further assistance.
The Motorola XPR 7550 can be programmed by using the RJ11 port in the back of the Motorola Impres Charger WPLN4243A. The WPLN4243A charger has a built-in interface that allows you to program your radio using the Motorola CPS software. This is done by connecting the charger to a computer via the USB cable, and then connecting the radio to the charger using the RJ11 programming cable. Once connected, the radio can be programmed and its firmware can be updated using the CPS software. It's important to note that the CPS software is not included with the charger and must be purchased separately. It's also important that you have the right version of CPS software that corresponds with your radio's firmware version.
The fast busy signal that you are hearing after a voicemail is left on your Motorola CD4 cordless phone is most likely due to a problem with your voicemail service or your phone line. Here are a few things that you can try to resolve the issue:
Contact your phone service provider: If the fast busy signal is being caused by a problem with your phone line or voicemail service, your phone service provider should be able to help you resolve the issue.
Reset your phone: Try resetting your Motorola CD4 cordless phone to its default settings. You can do this by unplugging the phone's base unit and removing the batteries from the handset. Wait for a few minutes and then reconnect the base unit and reinstall the batteries.
Check your voicemail settings: Make sure that your voicemail settings are configured correctly. Check your phone's user manual to see how to access and adjust your voicemail settings.
Try a different phone: If the problem persists, try using a different phone on the same phone line. If the different phone works properly, the issue is most likely with your Motorola CD4 cordless phone.
The Motorola XPR 4550 is a two-way radio, not a scanner. Scanners are devices that can listen to a wide range of frequencies, whereas two-way radios are designed for communication between a limited number of specific devices on specific frequencies. However, you can use a scanner to listen to the frequency that the Motorola XPR 4550 is transmitting on.
