A squealing noise during the sensing cycle of your Maytag top-load washer can be caused by a number of factors. Here are some common reasons and steps you can take to resolve the issue:
Loose belt - The noise could be caused by a loose or worn belt that needs to be tightened or replaced. You may need to remove the front panel of the washer to access the belt.
Idler pulley - If the idler pulley that keeps tension on the belt is worn or damaged, it can cause a squealing noise. Replace the idler pulley if necessary.
Bearing - A worn bearing in the tub can cause a squealing noise. Replacing the bearing will typically require disassembling the washer.
Drive motor - If the drive motor is worn or damaged, it can cause a squealing noise. Replace the drive motor if necessary.
If you're not comfortable diagnosing and repairing the issue yourself, it's best to contact a qualified appliance repair technician for assistance.
The first step to fixing the inner element of a Maytag Precision Touch Control 800 Electric Slide-In Smoothtop is to check the power supply for the range. Make sure all connections are secure and that the outlet is working properly. If the power supply is fine, then you may need to replace the inner element on your range. It would be advisable to consult the manual
Black spots on clothes from a washing machine can be caused by several issues:
Detergent buildup: Clean the detergent dispenser to remove any buildup.
Hard water deposits: Install a water softener to remove minerals that can leave spots on clothes.
Lint buildup: Clean the lint filter to prevent lint buildup.
Poor-quality detergent: Switch to a high-quality detergent.
Agitator problems: Check the agitator for any damage or issues.
If the issue persists, it is recommended to have a professional technician diagnose and repair the problem as it may require technical skills and specialized tools.
It sounds like there could be an issue with either the control assembly or the wiring between it and the washer or dryer. I suggest having a qualified technician take a look at your washer and dryer to check the wiring and control assembly for any problems. The technician should also be able to help you determine the cause of the issue and advise you on how to proceed.
Question edited for clarity and add 'maker model (what it is)'.
Question moved from Speed Queen to Maytag.
In cold weather an old belt become hard and stiff. When it warms up it is fine. You can either change the belt or you can spray it with Belt Conditioner which helps to soften the rubber and also makes it stickier.
https://www.google.com/search?q=la712+adjust+belt+tensioner
Belt conditioner
https://www.google.com/search?q=belt+conditioner
This issue could be caused by a number of things. It is possible that the clothes are not properly balanced in the wash drum, causing them to wrap around the agitator. It could also be a problem with the agitator itself, or with the transmission.
If your Maytag MDE4658AYW electric dryer is running hot on all settings, even on air fluff, it is likely that the heating element is not working properly. Make sure that the heating element is securely connected to the dryer and that the power switch is in the "on" position. If the problem persists, you may need to replace the heating element or contact the manufacturer for assistance.
I'm sorry but I'm unable to find the cubic feet size of Maytag dryer model SDG515DAWW. However, you may be able to find this information on the Maytag website, in the product manual, or by contacting Maytag customer service. Additionally, you can measure the interior dimensions of the dryer to estimate the cubic footage. The interior width, depth, and height measurements, when multiplied together, will give you an estimate of the cubic footage.
If your MSS25C4MGZ00 Maytag refrigerator's icemaker is not getting water, here are a few steps you can take to troubleshoot and fix the problem:
Check the water supply: Make sure that the water supply valve to the refrigerator is fully open and not restricted. Also, check that the water supply line is not kinked or frozen.
Check the water filter: A clogged water filter can restrict the flow of water to the ice maker. Replace the water filter with a new one and check if the icemaker starts working.
Check the water inlet valve: The water inlet valve controls the flow of water to the ice maker. If the valve is defective, it may not open to allow water to flow to the ice maker. You can check the valve for continuity with a multimeter, if there is no continuity the valve needs to be replaced.
Check the icemaker control module: The icemaker control module controls the operation of the ice maker. If the module is defective, the icemaker will not function. Check the continuity of the module with a multimeter, if there is no continuity the module needs to be replaced.
Check the water pressure: Ensure that the water pressure to the refrigerator is between 20-120 psi. If the water pressure is too low, the water valve may not open to allow water to flow to the ice maker.
If you are not comfortable working on your own, it is recommended to contact a qualified technician to diagnose and fix the problem. It is important to note that troubleshooting and repairing a refrigerator can be dangerous, so it's important to follow safety precautions and make sure you are familiar with the appliance before attempting to fix it yourself.
It sounds like you are having trouble getting the lid on your Maytag Bravo top-load washer to close properly, even after replacing the lid strike and the lid latch. There could be a few reasons for this issue:
The lid strike and latch are not properly aligned: Make sure that the lid strike and latch are properly aligned and that the strike is lined up correctly with the latch.
The lid strike is not adjusted correctly: The lid strike may need to be adjusted in order to properly engage the latch. Check the installation instructions for the strike to see if there are any adjustment instructions.
The lid latch is in lock mode: Some Maytag Bravo top-load washers have a lock mode that prevents the lid from being opened during a wash cycle. Make sure that the latch is not in lock mode by checking the owner's manual for instructions on how to unlock the latch.
The lid strike or latch are defective: If you've tried the above steps and the lid still won't close, the new strike or latch may be defective. It's recommended to contact the manufacturer for further assistance or to contact a professional technician for repair.
It's important to make sure that the lid is closed properly before starting a wash cycle to prevent water from leaking out of the washer.
Not quite sure about your problem but, if it is a wood screw going into your door, you can take the screw out a insert a hardwood toothpick into the screw hole and reinstall the screw. this will fill any stripped out of the hole and screw should fit securely. If it is a metal to metal problem you can go to the hardware store or even walmart and buy a product called " Locktight". it is a liquid that you put on the screw and reinstall it. it will dry and lock the screw in place. Buy the blue if you want to eventually take it out at some point or buy the red, if you want it to stay in place and take a lot of effort to get it back out.
If you smell gas coming from your Maytag Gemini range, it is important to take immediate action. Gas leaks can be dangerous and can cause fires or explosions. Here are a few steps you should take:
Turn off the gas supply to the range: Locate the gas shut-off valve for the range and turn it to the "off" position. This will stop the flow of gas to the appliance.
Open windows and ventilate the area: Open windows and doors to allow fresh air to circulate. This will help dissipate the gas fumes.
Do not use any electrical switches, appliances, or light fixtures: The sparks from these devices could potentially ignite the gas.
Leave the house: If you suspect a gas leak, it is best to evacuate the house and go to a safe location.
Call for professional help: Contact a gas company or a licensed appliance repair technician to repair the gas leak and check for any other issues with the appliance.
It seems that the 7601P428-60 timer control is a discontinued part and may no longer be available from Maytag or other retailers. Your best bet for finding this part would be to check with appliance repair shops in your area, as they may have used or refurbished parts available. You could also try searching online marketplaces such as eBay or Etsy, as well as appliance forums or Facebook groups where people sell or trade appliance parts. Keep in mind that these sources may not always have the part in stock, and it may take some time and effort to find a seller who has the part you need.
Press and hold the clock button for at least 3 seconds to stop the sabbath mode. This should bring it back to normal operation. If not just respond here and I can walk you through the lengthy diagnostic cycle to clear it.
