Unfortunately, if you can't get to it, you need a new machine. Normally you would seal with silicone or epoxy putty. The only thing I can can think of is injecting polyurethane expanding foam into the area, but go easy it expands for 10 minutes and you would have to shield any moving parts.
Most parts are obsolete.
You will need to replace the 20 amp. ceramic fuse inside the unit. This is real easy and the fuse only cost around $10.00 You will find a break down of your unit at www.partselect.com just enter your model number and a break down will come up. Your part number is PS2052772. You can also locate where the part goes. Good luck.
es, in order to remove the top of a Maytag LSE1000 washing machine, you'll need to first disconnect any attached wires. This is because the wires are connecting important components like the control panel and the sensors to the rest of the machine.
Here are the steps you can follow to safely disconnect the wires:
Unplug the washing machine: Before you begin, make sure to unplug the machine from the power source to prevent any electrical shock.
Locate the wires: Look for the wires that are connecting the top of the machine to the rest of the machine. They should be near the back of the machine where the top and bottom halves of the machine meet.
Label the wires: Label the wires so you know which wire goes where when you're ready to put the machine back together. You can use masking tape and a marker to label each wire.
Disconnect the wires: Gently pull the wires from their connectors, making sure to keep them separated so they don't get tangled. Be careful not to pull too hard, as this could damage the wires or the connectors.
Repeat the process for all the wires: Repeat the process for each wire until they're all disconnected.
Once you've disconnected all the wires, you should be able to remove the top of the machine. Make sure to keep the wires organized and in a safe place while you're working on the machine. When you're ready to reassemble the machine, simply reconnect the wires in the reverse order you disconnected them.
https://search.yahoo.com/search?fr=mcafee&type=E210US1494G0&p=the+electrical+capacity+of+Maytag+MDG9700BWW%3F
Then check related searches
MOTOR: 1/4HP,120 volt,60 Hz,single-phase,thermally protected against overload,auto-reset. EXHAUST:Use a minimum of 4"(10.2 cm) diameter rigid aluminum or galvanized steel duct. Never use plastic,nonmetal or combustible duct. HEAT SOURCE/ELECTRICAL REQUIREMENTS: Electric model- 5,300 watt nichrome helix coil; 240 volt,AC,60 Hz; 30 amp fuse. Gas model-Single port burner with automatic electric ignition; 22,000 BTU/hr. 15 amp fuse. Self-adjusting valve automatically compensates for variation in gas pressure. WEIGHTS (Crated/Uncrated):
The F70 indicates a communication error code between the main control on the top left and the user interface on the front. Unplug the machine and remove the top. Check the connection on the board in the white plastic housing on the top left. Next check the connections on the board on the front.
El c?digo de error "od" en una lavadora Maytag Neptune TL generalmente indica un problema relacionado con la apertura de la puerta. "od" es una abreviatura de "Open Door" (Puerta Abierta en ingl?s). Aqu? hay algunas acciones que puedes tomar para solucionar este problema:
Verifica la Puerta: Aseg?rate de que la puerta de la lavadora est? completamente cerrada y que no haya obstrucciones que impidan que se cierre correctamente.
Reinicia la Lavadora: Intenta reiniciar la lavadora. Descon?ctala de la corriente el?ctrica durante unos minutos y luego vuelve a enchufarla. Esto puede restablecer la electr?nica interna y eliminar el c?digo de error.
Inspecciona el Pestillo de la Puerta: Verifica el pestillo de la puerta para asegurarte de que est? funcionando correctamente. Si el pestillo est? da?ado o desgastado, podr?a necesitar ser reemplazado.
Comprueba el Cableado: Examina el cableado que conecta el interruptor de la puerta y el panel de control. Aseg?rate de que no haya cables sueltos o da?ados.
Sensor de la Puerta: Algunas lavadoras tienen un sensor de la puerta que puede fallar. Consulta el manual del usuario de tu lavadora para obtener informaci?n espec?fica sobre la ubicaci?n del sensor de la puerta y c?mo comprobar su funcionamiento.
Llama al Servicio T?cnico: Si despu?s de intentar estas soluciones el problema persiste, es posible que necesites la asistencia de un t?cnico de servicio. Puede haber un problema m?s complejo con el sistema de la lavadora que requiera atenci?n profesional.
Recuerda que estas son sugerencias generales y pueden variar seg?n el modelo espec?fico de tu lavadora. Siempre es recomendable consultar el manual del usuario de tu electrodom?stico para obtener informaci?n espec?fica sobre los c?digos de error y las soluciones recomendadas. Si no tienes el manual, puedes buscarlo en l?nea o contactar al servicio de atenci?n al cliente de Maytag para obtener asistencia.
I always leave the door cracked open so air can circulate in there and dry it up till there is no mold I've never had a problem I've had this washer 17 years
notify a repair company for quotes or online search for part ----fixya is an online repair forum we dont send repair personal out or sell manufacture or ship products
Unplug your washing machine for a few minutes which will let the electrical charge to dissipate from your washing machine that will let it reset then. If it is still not working unplug it for 10 minutes.Or you will have to access the real switch then which is under the lid housing by pushing the washing machines drum to the back.
This may sound silly and I know your stove is gas, but is your stove plugged into a power outlet on the wall? Some older stoves had the igniters powered from a wall socket so had to be 'plugged in' and others are powered by replaceable batteries, (AA's or AAA's), with the pack being mounted low down on the front, near one of the front feet. If it is a battery type try changing the battery for a new one. Sometimes the fix is that easy.