Mastercraft Vacuums - Recent Questions, Troubleshooting & Support

Could be worth looking on eBay.

Hi
Sounds like you have dirt/debris in your caburetor jets,fuel passages .
Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
Note:Before you disassemble the carburetor:
Write down on a piece of paper and or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.
Mark each piece with a awl, or some kind of sharp instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.
That way you will know which way it goes back together when you reassemble it.
Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.
Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.
Check you fuel line/s condition...after a while they will degrade and need replacement.
Check/Clean/Replace your fuel filter if you have one.
When you remove your fuel lines from the carburetor be sure to make a drawing or take a picture of how the lines are connected to the carburetor.
Also a good time to take a picture for later reference for reassembly.
If the mower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.
The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.
Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.
Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.
Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.
Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.
When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.
But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.
Be sure to mark the turns down on a piece of paper.
That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.
Once you have your carburetor cleaned/rebuilt that should solve your problem.
Please take time to rate me thumbs up

That would depend on the make and model of the steamer.

Replace the part that is faulty. Here is the parts lists. https://www.google.com/search?q=Bissell+1713+Crosswave+parts+diagram ..

To turn off the LED service light on your Aerus CentraLux central vacuum model E130J after replacing the motor, switch the blue box on the circuit board from "ON" to "MEDI."

Alot depends on the type of hose. There are plastic hoses and rubber hoses. Generally you can use a smaller plastic connector to connect two rubber hoses together and visa versa, Make sure it is a snug fix. You could also use an adhesive to keep it together.

We don't have any service centres at all! We are Fixya dot com. We are a peer to peer self help group. We don't sell anything, we only provide free information. Here are a few service centres in Bacor. If you need further help, click Comment under my answer. Let me know 'make model (what it is)'. https://www.google.com/search?q=Bacoor%2C+Cavite+service+centre ..

Question edited for a lot more clarity. It indicates that it is charging. https://www.google.com/search?q=Electrolux+Ergorapido+EHVS2510AW.+The+blue+light+stays+on ..

How to open it to see if the fuse is blown. I removed the three screws I saw. I feel that there is another which prevents me from opening it in two. I looked under the tights, I removed the plate where the two buttons are located. I can't open it.

Singhal Industries produces biohazard plastic bags with high-quality materials and stringent manufacturing standards to ensure durability and containment of hazardous materials. Their bags are specifically designed to meet industry regulations and ensure safe disposal practices.

try cleaning the filters if they are blocked then suction is lost and would appear like bag was full. hope this helps

press time\alarm button three times for min hand and again for hour

Hi the lid on my miele where tools go isn't latching how do I fix it plz

check eBay , amazon or call number listed in instructions.

there is a reset button on the side of the lower base of the machine, plug in the unit turn on the switch to the brush and vacuum are both engaged hit the reset button, remember the roller will not engage when the handle is in the upright position, release the handle and your ready to go.let me know if that helped you . thanks renevacdoc

I had the same problem. Red light would come on after charging was complete. On investigation I found that there is a small gray wire that runs from the rear batteries to a large solder spot on the control board. Upon re-soldering this wire I got an additional 3 V of power and the red light does not come on anymore after it is charged. I can vacuum the whole house and then some and still not run the batteries down.

Question edited to add CAPS, sentences and punctuation! All questions need full 'make model (what it is) first 3 words. The likely reason is a bad connection, or it is supposed to turn on with the 'hose switch'. Google make model manual ..

Sounds like the seal split. Strip it down, clean, replace the motor and seals.