Makita Drills - Recent Questions, Troubleshooting & Support


Some of the Makita 18v LXT tools require the BL1830 3.0AH battery and are designed that the 1.5AH battery will not fit.

Makita 18V LXT... | Answered on Sep 14, 2019


What has happened is the hex part of the bit has twisted slightly making it hard to remove. What I would do if you are comfortable with partial disassembly is remove the quick release mechanish. There is a split ring that comes off first and then a washer and spring, next remove the outer collar and SMALL steel ball from side of chuck. I take a pick (dental tool) and push up or try and twist the stuck bit. Sometimes it takes while but usually this works. Let me know if I can try and help further.

Makita 18V LXT... | Answered on Aug 27, 2019


you can buy the part
exploded view says part 6
look simple ..?.the way in is undo the top casing
leave the motor section in place if possible
Makita 3700B Trimmer Parts

Makita Drills | Answered on Aug 24, 2019


7.2V LITHIUM-ION 1.0AH (BL0710)
The Makita 1.0Ah battery with a 30 minute charge time.

Lithium-ion (LXT) - Makita


https://www.makitauk.com/lithium-ion-lxt.html

Makita Drills | Answered on Aug 15, 2019


The brushes are probably wearing out. They can also smoke if they get dirt or something on them. You can take the drill apart and replace the brushes, but if they are just burned some, take some fine sand paper or emery cloth and polish the armature where they run and clean the brushes and reinstall.

Makita Drills | Answered on Aug 15, 2019


On the Makita 18-V DC18RA charger, the flashing red light means that the battery is not at the correct temperature for safe charging. If the battery is hot (from use or being in direct sunlight), charging will begin when the battery cools down. If the battery is cold, then charging will start when the battery warms up. (Note: the cold battery could have moisture condensation issues. This could delay the start of the charging cycle.) Home Depot has the manual for this charger here: https://images.homedepot-static.com/catalog/pdfimages/35/35393127-7c0b-4668-8609-9104ae7cc187.pdf . I suspect that Makita uses the same "code" on all of their chargers.

I hope this helps.

Cindy Wells

Makita Drills | Answered on Jun 25, 2019


You can try to recharge batteries and see if they work by placing them in tool. If you are using Ni cad batteries and charger, you would better served by going lithium ion batteries.

Makita Drills | Answered on Jun 07, 2019


  • Defective battery
  • Defective charger

Makita Drills | Answered on May 20, 2019


I’m not sure if you can buy a new c/board .
The charger tests the battery before charging & if it picks up a fault it won’t charge the battery. At our repair shop we just replace the whole battery ( under makita warranty if it’s under two years old / depending on what warranty your country has )

Makita Drills | Answered on May 12, 2019


Unfortunately, Makita’s li-ion battery packs have a design flaw. After having the same problem with my two batteries, I took it apart and saw the problem immediately. You see each battery pack has ten li-ion battery cells and a circuit board with a memory chip witch holds the charging history of the battery pack. But that memory chip constantly draws power from 2 of the 10 batteries. The current it draws is very small but if you consider it over 8 month or more, the power drain becomes very significant. You end up with a battery pack with 8 still fully charged battery cells and 2 drained battery cells. When you put this battery pack in the charger, it detects weak battery cells, assumes they are defective and refuses to charge. To avoid this problem you should charge your battery pack often, even if you haven't used it, every two months should be ok.
I suspect that Makita doesn’t make these battery packs, they make power tools, good ones too. Buy Makita should definitely have a few words with their supplier before they become a liability!

Makita Tools 18V... | Answered on Apr 23, 2019


Having same issue with different model charger...skil....
Might be a fuse or something inside charger blown maybe, as I'm reading it could be somewhere online. Not positive on this.

Makita 2 Bl1830... | Answered on Apr 21, 2019


MOST mAKITA POWER TOOLS HAVE A 3 YEAR WARRANTY. THEY MAY REPAIR OR REPLACE YOURS AT NO CHARGE. DON'T WORRY ABOUT RECEIPT UNTILL YOU CHECK. DATE OF PRODUCTION ON TOOL MAY BE ENOUGH PROOF.

Makita Drills | Answered on Apr 01, 2019


CONTACT MAKITA WEBSITE AND ASK TECH SUPPORT .I CAN THING OF NO REASON

Makita Drills | Answered on Mar 25, 2019


Do not keep her on cold place. sorry but you have to buy new one again :/ take a look on amazon or something:
Amazon com Makita 18 battery

Makita Tools 18V... | Answered on Mar 18, 2019


The DC18RC are most likely to charged the BL1830 battery, which is the most popular of 18V Makita power tools. It is a Li-ion battery.

And the DC18RC battery charger has two volt 110 Volt and 240 Volt.

The 240 Volt DC18RC charger can replace model DC18RA & DC18SD because of its improved performance and full compatibility with Makita's NEW 'Star' labelled batteries that communicate between the tool, battery & charger. And, it is a fast charger.

It can charge a Makita BL1830 Battery in approx 22 minutes.

But, I do not recommend to convert a makita charger model DC18RC at 110 volt to 240 volts.

The reason is as below:

1. This will void product warranty ! If you follow this mod, you do it on your own risk !

2. There are several comments that described
same model # but with different design and components.
Please beware that this mod might not work on your charger
or worst, will damage it.
Only perform this mod if you know your way around with electronics !

Makita Drills | Answered on Feb 26, 2019


Yes, there should be a couple of tiny holes in the brush holders you can push tiny Allen wrenches in to hold brushes back against springs to clear armature to assemble.

Makita Drills | Answered on Feb 10, 2019


go to Makitatool.com and type in your model number and you should be able to download a schematic, if you have a problem let me know and I will go another route for you.

Makita Drills | Answered on Jan 13, 2019


MOST REVERSIBLE DRILLS HAVE A SCREW HOLDING THE CHUCK ON . OPEN THE CHUCK TO MAX AND LOOK DOWN INSIDE IT WILL BE LEFT HANDED THREAD UNSCREW IT AND CHUCK SHOULD FALL OFF ALMOST

Makita Drills | Answered on Dec 14, 2018


The serial number is on the main label. Unfortunately they have a habit of wearing off.

Makita Drills | Answered on Dec 11, 2018

Not finding what you are looking for?
Makita Logo

1,052 questions posted

Ask a Question

Usually answered in minutes!

Top Makita Drills Experts

John Trevino

Level 3 Expert

1420 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Spud Howell

Level 2 Expert

66 Answers

Are you a Makita Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...