Linksys Popular Questions, Answers, Tips & Manuals

You can log into it by using the internal ip address of 192.168.1.1.

by default it uses the most strong signal to connect. You can change connections manually - no exact steps since have no idea what system you're running on

Follow these directions: How To Setup the Linksys WRT54G Wireless Router for EarthLink DSL

If you don't know how to install Linksys 3500 router password setup then you follow the given steps:- 1. Login the Admin. 2. Click on Advanced 3. Go to the Administration 4. Click on Set password 5. Enter old password. 6. Enter New password. 7. Repeat New password. See image & Visit- http://www.linksysrouter.supportphonenumber.com/

You will need to reset the device.

if there is console port, connect via putty software and do a command base reset. http://www.manualslib.com/download/96063/Linksys-Slm224g4s.html

The password is wrong, or the phone does not support the protocol on the wireless router.

The manual, here : https://www.timewarnercable.com/content/dam/residential/pdfs/support/WirelessRouters/linksys_wrt54g_ug.pdf gives on page 20 this:

It's a wireless router, so you may not need to use a port at all. You can connect to any of the ports numbered 1 through 4. The yellow Internet port should connect to your outside network. (Cable modem or router or Ethernet port from your Internet service provider.)

http://support.linksys.com/en-us/support/routers/E800

Find the reset button on the router, then hold it down for around 30 seconds to a minute. This should reset the router to factory default settings.

Hi Bess, I've attached the user manual for this router for you to look through. The setup instructions are on the first couple pages. Hope this helps! http://downloads.linksys.com/downloads/userguide/1224638332121/WRT100_ug.pdf

LOST ROUTER LOGIN PASSWORD If you have forgotten your personal router login password there is no way to recover it. You will have to reset the router. This means all the settings on the router will be reset to factory defaults. It also means that all your connected devices will need to be connected again with the new security information (WEP, WAP, etc,) . You will need the default admin login name and the default admin password. This can be found in the user guide that came with the router. This can usually be found online at the router manufacturers site. There is usually a button or a switch hidden in a pinhole opening on the back of the router. Pressing and holding the switch for 10 seconds or so will cause the reset and usually the LEDs will flash and blink for several seconds as the router firmware resets and clears out the old information. If you are trying to get into someone else's router illegally there is no way to find out their login password. For future reference, write the password down, or a hint at what the password is, on a piece of tape and secure it on the bottom of the router. I use my cell phone memo function to store all my passwords. Linksys Home Networking

You are not entering the correct router WPA/WPA2?PSK password.

Reboot the PC. Web stack probably needs resetting.

Using web browser enter the default ip of the linksys device. Make sure a port on the router is connected to your PC. Also ensure you configure the PC is on same subnet as your router. Login with the default credentials. This should take you to the router interface where you can set up SSID and security for your WIFI

You'll have to call whomever you ordered it from and tell them you want to cancel.

for securing your linksys router, first you need to connect your linksys router with computer via cable. then you need to open router setup page on your browser. Once you will be there , you need to click on wireless security. now you need to select your wireless protocol and type your password in. Finally you need to click on save settings and your password will be setup . you can enjoy with it. Thanks,

Linksys 2.4G What? what model?

There is no way for us to tell you that. You could have to contact whoever you setup the email address with.