Password of linksys spa 2102
The Linksys comes with web admin access disabled.
To enable it, pick up phone, dial **** then 723646# , when asked for password, dial 78778839# , when asked for value dial 1# then dial 1 to save.
Then, go to »192.168.0.1/admin/voice/advanced , enter user and password.
If you did a factory reset, you will need to call Linksys technical support.
How do i hook up
First of all, we all know that wifi means Wireless fidelity. So we can use it on our phones. it's like a wave. but when we want to connect our pc which doesn't have nic card then we have to use wire which connected to wifi\router. By the way, if we want to hook up a wireless router to a cable router we have to take some process. as like connect the router and the modem with an Ethernet cable. Most routers come packaged with a short Ethernet cable that you can use for this. otherwise, the isp provider gives us a short cable for pc and laptop when the internet connection complete with the router. then we can easily connect the wireless router to a cable router. Once the cable router is finished syncing-up and the cable router should provide an IP address to the wireless router.
https://www.allhdd.com/networking-devices/router/
12/31/2020 3:15:36 AM •
Linksys...
•
Answered
on Dec 31, 2020
How can i find out my pssword.
The default username and password for Linksys routers are:
Username: admin
Password: password
or
Username: admin
Password: admin
or
Username: <no username>
Password: password
If all of this fail you'll need to reset your linksys router so that it will also reset the password to the default. To reset you linksys router you can check it out on this website:
http://technicallyeasy.net/2008/01/how-to-reset-linksys-wrt54g-wireless/
Note: Reseting your router means it's going to reload the factory default settings and all of the settings that you made on your router will be deleted permanently.
3/20/2020 12:44:35 PM •
Linksys...
•
Answered
on Mar 20, 2020
Why is my Linksys WRT54G wireless-g router not being recognized anymore?
just fixed one yesterday.
the power pack was no good.AC wall wart,
power green LED blinked endless. and the white logo, LED is dead..
a new pack fixed it.
also the wrong pack used, ! do not mix them up. oops.
first year 54G, v1 uses 5vdc pack.
at v2, and up all want to 12vdc pack,
bottom sticker on above failed was v6.
you said recognized, does that mean the 4 rear Ethernet wired jacks are dead, or just wifi dead.?
first the ethernet ports must work, or wifi is doomed.
2/18/2020 11:46:05 AM •
Linksys...
•
Answered
on Feb 18, 2020
How to fix Linksys router error 321 ?
Good day,
This might be of help .
Steps To Fix Linksys Router Error 321:-
Step1:- Check the Firewall Settings
To check the Firewall Settings is the first priority for the users. Then check the firewall settings of the computer/ Laptop, will be helpful to find the problem. If there is any firewall installed on the computer, so the users need to turn it OFF.During the process, the users ensure that the Local Area Connection on the computer is not disabled. The Local Area Connection should not have any static IP address assigned. If there is any then the users need to immediately set the IP address to automatic.
Method2:- Run the Installation CD Again:-
The users require trying to run the CD again and ensure when the CD runs, it will ask to connect the computer and the modem to the router with the cable. So the users will need to notice, that there all the lights lit up on the router. If it's not, then users will need to setup their router without the CD.
The users can get the instruction to setup router manually in the method 3.
Step3:- Try to Setup Router Without Installation CD
Setup Linksys Router without Installation CD is another best option for users in order to completely avoid the in order to fix Linksys Router Error 321.
Follow the below-given instruction to Setup Linksys Router without Installation CD:
First of all, connect the main computer to the Ethernet port on the router.
Then the users need to connect the modem to the Internet port on the router.
Now it's time to verify the status of the light that is blinking properly.
Next, users need to open the setup page of the Linksys Router and then change the Internet connection settings manually.
In the setup page of the Linksys Router, the users can change the settings of the router as per their needs.
Then the default IP address of many Linksys router is 192.168.1.1. And the default username and password would be an "admin".
Wait for a few minutes, when the main computer is able to access the Internet, so users need to create a wireless network for their wireless computers/devices.
or you can call them @ Toll Free 1-800-204-6959 that is Lynksys support.
2/3/2020 1:14:25 PM •
Linksys...
•
Answered
on Feb 03, 2020
AOL Broadband Cable
The following routers are the only models that support the AOL Broadband Cable service.
Note: All Linksys routers support AOL DSL connections due to the standard PPPoE login and authentication connection type used with that service.
Please be sure to check the version number of your router (which can be found on the underside label). Only the specific models and versions listed here are supported by AOL Cable:
*
BEFW11S4
*
BEFW11S4 v2, v3, and v3.2
*
BEFSR41
*
BEFSR41 v2
*
BEFSR11
*
BEFSRU31
*
BEFSR81
*
BEFSR81 v2
*
HPRO200 (Available from AOL only at this time)
You must Enable the "AOL Parental Controls" option located in the Security tab of the web-based Setup utility pages of these routers in order to get a connection using AOL Cable. You may access the utility by visiting http://192.168.1.1 in a web browser and by logging in using the router's password (by default, the password is admin).
Lost password for linksys 2.4 router
Step 1 : Connect - Router - Computer ( Wired )
Step 2 : open Router Setup by typing http://192.168.1.1 on the address bar of internet explorer
Step 3 : Default password is admin
Step 4 : Click wireless
Step 5 : Choose wireless security
Step 6 : Here you can find the Password
Step 7 : Try to connect with this password
let me know if this works
Regards
TOM
1/28/2020 6:56:16 AM •
Linksys...
•
Answered
on Jan 28, 2020
I cannot Log on to 192.168.1.1 - admin
In order for us to help solve you problem you have to tell us what you are doing.
Just making a statement is not enough.
My answer is wear green socks.
That's just as much use isn't it?
12/4/2019 6:12:03 AM •
Linksys...
•
Answered
on Dec 04, 2019
Disable internet access
Access your router Setup page
Open internet explorer
go to http://192.168.1.1 (default)
username: admin (default)
password: "leave it blank" (default)
Go to Security
go to Filter
if you know that Ipaddress of the computer you want to block for example 192.168.1.10
You can create up to five different IP Address Range filters
Users who have filtered IP addresses will not be able to
access the Internet at all If you only want to filter one IP
address instead of a range of IP addresses, enter the same
value into both fields For instance, if you wish to filter the
PC with the IP address of 192 168 1 5, enter 5 into both
fields on one line: 192 168 1 5 ~ 192 168 1 5
if you know the MAC address of the computer click the Edit MAC Filter Setting and input the MAC address you want to block.
blocking by MAC address is the most effective solution to block a computer... while blocking by ip address will be easily bypass by changing the ip add of the pc
then saved your settings and reboot..
How to Set Up Linksys WRT54G Wireless G Router
The vent actuators are bad. there should be two. one on each side. they are small toy like motors that open and close the vents from within to allow the hot air to blow by closing the vents to the a/c unit.
11/21/2019 5:05:43 AM •
Linksys...
•
Answered
on Nov 21, 2019
Not finding what you are looking for?
