Line 6 Low Down 400 bass guitar head
Make sure the volume and master volume are turned up. Try the amp with a different cabinet and a known good speaker cable. If you get sound, it's your speakers or your speaker cable.
If still no sound, you need your amp serviced.
10/20/2018 1:02:56 AM •
Line 6 Music
•
Answered
on Oct 20, 2018
•
222 views
My Line 6 Spider III
I suspect the power cord or it's connector is fasulty. That wouldbe the easyiest fix.Past that, it would need to go to an authourized Line 6 repairman.
Hd400 power
Line 6 has a network of authorized repair centers listed on their site. Due to the complexity of the device and the possibility of needing specialized parts, i suggest t you find the repair center nearest you and have them look into it.
Just purchased a new Line 6 HD 400 from the local
I've had both very good and very bad customer service from Line 6 over the years, Personally, Id take it back to GC and have them explain what you need.That way if it's a case of a defective item, they can replace it on the spot,
I have the Line 6 Spider 3 15 watt. My friend
Hey I have the same problem on the one i just bought for 10 bucks, I was wondering if you could tell what the pink tube thing and the white tube things near the semiconductor that was screwed to the metal are? are they capacitors or what? please help.
5/15/2016 12:10:51 AM •
Line 6 Spider...
•
Answered
on May 15, 2016
•
1,012 views
Where can i get a schematic..
I've also been looking HD500 schematic, but never got it.
You can use X3L schematic as a reference and compared.
Some sections of the X3L diagram, similar to the HD500.
By the way, what is the problem with your HD500? Maybe I can help or share.
HD500
X3L
How to remove chassis line 6 spider 111 30
Remove the retaining screws from the top and sides of the amp. The handle may need to come off as well. Remove the chassis from the cabinet from the rear by droping the rear of the chassis about 45 degrees and lifting the faceplate over the baffle board.It will be a snug fit.
11/25/2014 10:52:01 PM •
Line 6 Spider...
•
Answered
on Nov 25, 2014
•
329 views
Flextone 3 one speaker not working
Then you either have a blown amp or speaker. Turn the amp off and move the wires from the speaker on the working side to the other speaker. If the other speaker works, you have a dead amp channel. if it does not, move the wires from the speaker on the non-working side to the other speaker. If that works, you have a dead speaker. Dead amp channel means take it to the shop. Dead speaker means buy a new one from Line 6 and install.
There is no factory recall on my pod xt pro
That's correct, there is no onboard recall. In order to reset, follow the instructions in this link-
http://line6.com/support/page/kb/_/pod/pod-20-podxt-family-pocket-pod-floorpods/pod-xt-series-factory-reset-reflash-and-firm-r491
Podhd400 not working
Try doing a reset as explained in this video-
http://line6.com/support/page/kb/_/pod/pod-hd300400/video-tutorial-pod-hd300-400-factory-reset-r214
Heating when powering on?
Be sure you are using the correct voltage power supply for your area. If so, it's likely you have an internal power supply part failing. Best take it to an authourized Line 6 repair center or return it to the factory for repair.
11/25/2014 10:32:11 PM •
Line 6 Line6...
•
Answered
on Nov 25, 2014
•
57 views
Not finding what you are looking for?