Check if the tray is full of liquid. If so, empty the tray and clean it thoroughly .
If the tray is not full, try resetting the unit by unplugging it from the power outlet for a few minutes. Then plug it back in and turn it on again .
If the problem persists, try cleaning the two little contacts on the tray. Make sure there isn't anything across the two wires that run the length of the tray. It doesn't take much to trigger the light .
If none of the above steps work, you can try contacting FoodSaver customer service for further assistance
Question posted to the category
Light Office Equipment & Supplies
How 'light' is light?
Light Office Shredder? Light Office Coffee Machine? Light Office Collator?
All questions need full 'make model (what it is) as first 3 words.
..
Disconnect it from the mains for 10 minutes.
If it is the type with a button, spray it with electrical contact cleaner.
If it has no button, you need to find which micro-switch on each burner is staying closed circuit? It is likely to be the one you used just before it did this. There is help below in video and text.
If the burners are clean and dry and the stove ignition switches are working correctly, it is likely that the spark module is defective and causing the continuous sparking issue. If the spark module is defective, it should be removed and replaced with a new one.
Jun 7, 2021
Question edited for a lot more clarity.
It is likely to be fuel starvation. Check the following;
The tank vent.
The pump bulb is the right way around, ARROW towards Engine.
Cut a section of pipe and see if the inner lining has delaminated. The grey fuel pipe is bad for this. Modern Ethanol fuels damage the lining. Black Tube is best.
Also I had a similar issue on an Evinrude and it was a linkage not connected to the carbs. Only one was actuating.
Check grounds and bad connections as David says.
Sounds like you may have an air restriction or a fuel flow issue. Check the air filters to be sure they are clean and that there is no debris in the carburetor or fuel tank. Then check to make sure the fuel flow path is clear, not blocked with debris or sediment. If those things check out okay then you may need to adjust the carburetor settings for maximum performance.
If your Canon MX350 printer is displaying a paper jam error message, but there is no actual jam, there are several things you can try to resolve the issue:
Check the paper path: Look inside the printer for any small pieces of paper or debris that may have become lodged in the paper path. Remove any visible obstructions.
Restart the printer: Turn the printer off, unplug it from the power source, wait for a few seconds, and then plug it back in. Turn it on and see if the error message is cleared.
Clean the rollers: Paper feed rollers can become dirty and cause paper jams. Clean them using a damp cloth and a small amount of water or isopropyl alcohol.
Reset the printer: If the printer is still not working, you may need to reset it. Consult your printer manual for the specific reset procedure for your model.
If these steps do not resolve the issue, the printer may require service
If all the LEDs in a circuit are lighting up but not staying on, there could be a number of possible issues. Here are a few things you can try to troubleshoot the problem:
Check the power supply: Make sure the power supply is providing the correct voltage and current to the circuit. If the power supply is not working correctly, the LEDs may turn on briefly but then turn off.
Check the connections: Make sure all connections between the power supply, the LEDs, and any other components in the circuit are secure and not loose.
Check the LED circuit: Check the circuit that connects the LEDs to make sure it is functioning properly. Make sure there are no breaks in the circuit, and that all components are functioning as they should be.
Check the individual LEDs: It is also possible that one or more of the LEDs may be faulty and not functioning properly. You can test each LED individually by removing it from the circuit and testing it with a multimeter.
If you have tried these steps and are still having trouble, it may be helpful to get a second opinion from someone with more experience in electronics troubleshooting.
Impossible to answer as you give no clue what on! The category you posted to also offers no clues 'Light Office Equipment and Suplies.
'make model (what it is)' as the first 3 words in every question please. There are 10,000 categories to choose from.
The bump knob rotates in the direction of the trimmer. you will need a pair of channel lock pliers or equivalent hold head with one hand and try turning knob with pliers first anticlockwise (to the left). if you hold pliers wring the knob will spin, hold pliers so that the bottom handle is on the inside.