Wax bag change
you need to add wax to treadmill belt lubrication system
Speed control
unplug and replug all connections, if not replace motor controller baord
I have 9500HR Treadmill Lifefitness, Lift keeps
RUN the software calibration for easy diagnostic and fix it. Go under the HOOD motor, and follow the steps.
The Steps for Newer
Style Console Calibration:
- Locate the calibration area on the rear or
underside of the console (a hole, near the console's center, that goes
through to the electronics board. (This hole should
not have a screw in it.)
- Insert a pencil (eraser end), into
the hole and feel around for the cal button (will click when
pressed).
- Press the button 2 times (with
the pencil eraser). The first click should show CL11 in the
console, the second click should show CL21.
- If the process was done correctly, and
CL21 appears in the console, you are in "calibration mode."
The next few steps consists of pressing buttons on the
console and observing settings. This will not
require any other tools.
- Press ENTER. CL22 should display in the
TIME window and (??) in the SPEED
window.
- Press ENTER. CL23 should display in the
TIME window and (??) in the SPEED window.
- Press ENTER. CL24 should display in the
TIME window and (??) in the SPEED window.
- Press ENTER. CL25 should
display in the TIME window and (??) in the SPEED window.
- Press ENTER. CL26 should
display in the TIME window. You should then see the letter
"E."
- Press ENTER. You should see "SS"
or "55" in the console.
- Push the STOP/START button. For
safety, at this point, you should step off, or be off, the treadmill.
- Push the ENTER button. The walking belt
should start to move, accelerate to maximum speed, then stop on its
own.
- When the belt stops, the
incline should self test by raising to its highest incline
position, then lowering back down to its lowest position.
- Once the incline test is complete, push
the POWER button 2 times. The unit should shut off and the console
should go completely blank. If this happens, the
treadmill is done calibrating and is ready for use.
If the letter "F" appears in the SPEED or
INCLINE window when the power button is pressed 2 times, the treadmill is
indicating a failure somewhere either in the SPEED or INCLINE (depending
on the window the "F" appeared in). Troubleshooting the failure would be the next step. God bless you
E2 error lift error
Replacement Parts for Fitness Exercise Equipment at SPORTSMITH
You have posted this question in the Stair Climber section, but the error you are listing is a treadmill error code. The following information should help.
Probable Cause
A) Incline control error.
B) Insufficient power source.
C) User exceeds weight limit.
D) Unit will not lift.
E) Unit thinks it is always at 0% incline and only lifts up.
F) 3 amp circuit breaker has tripped.
G) CPU board has stuck relay.
H) Lift motor is faulty.
Corrective Action
A) Access the incline manual mode in diagnostics by pressing 9, 1, 9, ENTER and then pressing HILL program key. Incline the unit with two people on the unit. B) Ensure treadmill is connected to a dedicated 120V, 20 Amp circuit.
C) Advise user of unit's weight limit of 300lbs (137kg).
D) Perform the lift test procedure by pressing 9, 1, 9, ENTER and then pressing HILL program key.
E) Inspect the home switch for smooth operation and inspect the wiring of the home switch for damage or poor connections. Inspect the lift motor cable connections and for the presence of the suppressor board (should only be 1).
F) Test the circuit breakers and replace if necessary.
G) Replace the CPU board.
H) Replace the lift motor.
LifeFitness 9500 Treadmill Lift Control Error
Not finding what you are looking for?