LG WM - Popular Questions, Answers, Tips & Manuals
Wm1814cw LG front load washer won't engage drain pump
Washer will not drain: The drain water pump is the main part in your washing machine that pumps out the water. If this is defective or has failed in any way, this will be the reason why your washer will not drain the water. Before you order a new drain pump, make sure to check the pump to be sure a small object like clothing or similar has not lodged itself inside of it causing the NO DRAIN issue and even a no spin issue?. If the drain pump is not clogged, you can test it with a multimeter and remove and replace if needed. Read more: HYPERLINK "http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/" l "ixzz3X2LbXMWJ" http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/#ixzz3X2LbXMWJ The washing machine drain hose is where the water flows through to get the water out. If this drain hose is blocked, kinked, bent, or clogged, the washer will NOT be able to remove the water from the tub. Check the drain hose to be sure it allows the water to flow freely. You can take the drain hose off and run water through it in your sink to be sure it is not blocked. If there is water STILL in the washer when you remove the drain hose, grab a bucket as the water will exit from where you disconnected it The water pump belt (to drain out the water) may have broke or become frayed or loose. If this belt breaks then it is unable to drain and remove the water from your washer. Inspect the belt to see if this is causing the NO DRAIN issue and remove and replace if needed. If the lid switch is not working as required it will cause your washer to not drain (and many other problems). This may be unlikely as a bad lid switch will usually cause your washer to also not agitate or spin. However on some models this can vary. The best thing to do if you have a suspected bad lid switch is to test it. It can fail electrically and or mechanically. If mechanical failure is the issue, you should be able to see if it is cracked, broken, or not in place to make contact with the lid. To test it electrically, use a multimeter set on Ohms and test it for continuity My advice is free cuz God is good!
LG WM1814CW Front load Washer dE error? I get the
Hello,
A dE error code indicates that the washer door was unable to lock. This can normally be resolved by performing a simple reset on the washing machine.
How to reset the washing machine:
1.
Press POWER to turn the washer off.
2.
Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
3.
With the power disabled, press and hold the START/PAUSE button for 5 seconds.
4.
Plug the washer back in, or turn the circuit breaker back on.
5.
For more information about how to reset your specific model, please refer to the owner's manual.
Press in on the door firmly and select any cycle. The washer door should lock, and the cycle should begin without an error code appearing on the display. If the cycle does not begin and the dE code appears again, repair service is required.
2/3/2018 2:48:02 PM •
LG WM1814CW
•
2,457 views • 0 helpful votes
LG WM3431 door won't unlock
did you unplug it,leave it unplugged for 5 minutes and plug it back in,if it's to hard to get to plug flip the breaker and leave the power off for 5 minutes or longer when you power it up again the door should unlock.here's a link to check hope it helps
https://www.google.com/search?q=lg+front+load+washer+how+to+manually+open+a+locked+door&oq=lg+front+load+washer+how+to+manually+open+a+locked+door&aqs=chrome..69i57.21935j0j8&sourceid=chrome&ie=UTF-8#kpvalbx=1
Wm2277hw is leaking water from the bottom...
Easiest start is to take the top off and check for leaks maybe using a flashlight. Top comes off by removing a couple of screws in back, the sliding it rearward about 3 inches and then lifting up. Good luck. Report back what you find. Use comments.
Washing machine dampers
damper is stiff. i would look at the springs that hold the tub if you take them off a bad one won t close all the way up also check leg mounts for weak medal
Lg tromm steam washer model:
Sal De
Go here,put your model number in to see all parts in your washer,if you think you can change out the hose then do it,find the hose on the diagram,get the part number and order it,or the hose could have pulled off from an unbalanced load but you're looking at it,if it has a hole in it replace it,if it just has to be realigned then do it.this ain't heart surgery lol.just unplug the washer before you open it up.good luck with it.
WW2277HW
My guess is replace the drain pump. Inexpensive part but kinda hard to get to. Check out repair videos on parts sites or YouTube
First 30 days with
Washer is about 10 years old. So check springs to make sure not broken(unlikely). Then check shock absorbers and see if they look good. Hard to check actual functionality. If you see a problem then that's your issue. If you see nothing, then I would just replace them. They don't last forever. Good luck.
My lg tromm wm2277hb wont
Suggest try same again.
Modern appliances have a zillion circuit connections of which any one of them can develop a "bug".
Unless it is under warranty it's usually less trouble and cost to simply replace it.
Just bought it used.
Washing to
Hi Santiago,
Make a basic check up of the outlet hose, if the hose is towards upward the water will remain in the hose or in drum this will change the system which will result in excess consumption of water. Hence make a straight passage towards ground so that u will find a good result.
Not finding what you are looking for?