It is difficult to answer without FULL 'make model (what it is)'. These projection clocks work in the same principle, but in two ways. The time is on a LCD film and light is shone through it, then through a lens and projected onto the ceiling. The projection light can be done in two ways;
A white LED illumination light and a red LED light that comes on via an electronic timer, say 5 minutes white and then red constant
or a single LED what is white or red depending on the voltage supplied to this variable voltage LED.
The only way to fix it would be to send it for repair as it is an electronic fault You could however check the manual in case there is a setting to turn off the Red LED. I had a CD Alarm Clock Radio and the projector was the first thing to fail followed by the rest of it 3 years later. I wasn't that worried as I won it in a charity raffle. My GE Alarm Clock Radio is still going strong 48 years later!
Google
make model manual
..
Question edited for clarity.
Questioned moved from Misc to clocks.
All questions need full 'make model (what it is)' as the first three words or it is all guesswork.
My guess is that you are in the wrong time zone and it will change in 2 weeks when it changes in the UK. You are set to GMT instead of PST, CT or EST.
..
To correct the time on your Sharp Atomic clock, you will need to reset the time zone. To do this, press and hold the "Time Zone" button for 3 seconds until the time zone flashes. Then, press the "Hour" and "Minute" buttons to adjust the time zone to the correct time zone. Once the time zone is set, press the "Time Zone" button again to save the settings. The clock should now be displaying the correct time.
If it dims as soon as you turn it on, then it could be a sign of a faulty power supply or a loose connection. You should check the power supply and connections to make sure everything is secure and functioning properly. If the issue persists, you may need to contact the manufacturer for further assistance.
There are a few potential reasons why your Bulova B1987 mantel clock has stopped chiming:
Check if the chime switch is in the "on" position. If it is not, switch it to "on".
Make sure that the clock is wound fully. A clock that is not fully wound will not chime.
Check if the chime melody selector is in the "off" position. If it is, move it to a melody position.
If the clock has been moved or bumped recently, the chime hammers may have been knocked out of alignment. This can be fixed by a professional clock repair person.
The chime rods or hammers may be damaged or worn out. This can also be fixed by a professional clock repair person.
If none of these solutions work, it may be best to contact a professional clock repair person for assistance in fixing the clock's chime.
Before deleting the current program and reprogramming your NX-8 wireless smoke detector, you may want to try the following troubleshooting steps:
Check the batteries: Ensure that the batteries in your wireless smoke detector are not dead or low. Replace the batteries if necessary.
Check the signal strength: Make sure that the wireless smoke detector is within range of the NX-8 control panel. You can try moving the detector closer to the panel to see if it helps.
Check for interference: Interference from other wireless devices, metal objects, or thick walls can affect the signal strength. Try removing any potential sources of interference or relocating the detector.
If these steps do not resolve the issue, then deleting the current program and reprogramming the wireless smoke detector may be the next step. Be sure to follow the instructions in the NX-8 programming guide to properly delete and reprogram the detector. If you are not comfortable with programming the system yourself, you may want to contact a professional alarm company or technician for assistance.
Unfortunately, without being able to see the spindle, it is difficult to provide specific instructions on how to remove it. However, in general, you should be able to remove the spindle by unscrewing it from the housing. You may need to use a pair of pliers or a wrench to get a better grip on the spindle. Once you have loosened the spindle, you should be able to pull it out of the housing.
You can purchase the long black screw assembly from the manufacturer of the Fashion Bed Group Bunk Bed. You can contact them directly to inquire about purchasing the part.
If the chime on your Daniel Dakota Grandfather clock has stopped working, it is likely due to a mechanical issue. You may need to take the clock to a professional clock repair shop to have it serviced. The repair shop should be able to diagnose the issue and make any necessary repairs.
The medicines should be taken in the right amount and at the right time. Due to memory problems the seniors are not able to take in a right way, so a medication dispenser for seniors can be a good solution for that. A pill dispenser contains all the medication details along with scheduled time details.
It is probably 'Westclox', not 'West Clock' and 70045? They are usually very basic with no adjustment. Some have an Automatic Light Sensor, or it may just be that the capacitor that powers the display is failing.
No manual
https://www.google.com/search?q=Westclox+7045+manual
