How to reset window settings on 1995 Lexus ls 400
ANGELOLISA.
JUST ONE DOOR FAILS.
WELL ALL FAIL FOR :
1: FUSE BLOWN
2; WIRES BAD
3 ;WINDOW GUIDE JAMMED up.
4: WINDOW MOTOR BAD OR ITS CHILD PROOFING CLUTCH BAD. (SAME REALLY)
5:CONTROLS BAD. AT DOOR.
A TECH DOES TESTS NOT JUST GUESS WILD.
USING A METER, CALLED A VOLT METER.
we check full 12vdc to the motor ,pushing up.
if good that is motor silent or sounds overloaded
it is or window is jammed.
so the tech pulls the motor driver and moves the window by hand oops its jammed. bad guides
Can a weak brainbox cause fuel to be mixed with engine oil
Why do you think there is fuel in the oil? Does it smell like it? Or is the dipstick level climbing? Tell us more about the problem and what you have already tried/done. When was the car last fully serviced? Poor maintenance is no excuse for poor running.
2013 Lexus RX 350 crankshaft position sensors is located where
NO COUNTRY TOLD at all. (sold to day1 new) no VIN told no VIN #8 digit told so we can see what engine is there. and what country, some have 8 engines choices not one I can guess and is a pure engine question the endless hunt here. 2 gas engines here and 1 hybrid , engine is TOYOTA's USA got the 3.5L V6, are you here? USA??? the USA engine has 2 pin CKP sensor, 2 pins is huge clue. crank sensors are on the cranks sure but are on front, middle or rear of crank or even under flywheel, 4 places all engines, 1 is true the cranks shaft has the CKP huge tone while dead front of crank. the service manual covers this, only or you can google this. toyota 3.5 L 2GR-FE V6 cranks sensor location bingo.(note using the real name)
2002 Lexus sc430 location of door chime
most cars IT is deep in the IP cluster
only the SM service manual shows this.
door AJAR CHIME
THE DOOR OPENS AND DOOR CPU SENDS THIS
DATA FACT TO THE CLUSTER, (ON THE MX DATA NETWORK AND THE CLUSTER CHIMES.
if the chime is bad say so? we can not guess goals.
or too loud or what?
here it is
Check engine light and vsc
Source:
What Does Your Check Engine Light Mean?
When the powertrain or engine warning light illuminates, it could indicate several issues. In addition, it does not have to be a significant problem, such as a misfiring engine; it could be something minor.
When a potential problem is detected, the car's computer will alert you, and the check engine light will illuminate. Typically, either the transmission or the engine is involved in these issues.
Regardless of whether you believe the problem to be minor or not, the check engine light should always be addressed immediately. The simple reason is that the exact cause of the warning is unknown.
Lexus RX400H won't start. Prior suddenly stopping the car was having temperature issue. It has been scanned with 3 different machines, but it is only picking light and ac error code.
2006 Lexus RX400H hybrid .and long story.(you added and very very good)and if was mine, my story would be same, park it and wonder what to next.?this car is very complex, unlike ICE real cars were simple and still are to a good extent.I do wish you find a good shop to cure all that.a full service manual in hand may do the trick.IDK.good luck! and be SAFE.use the scan tool as the hybrid starts and fails to light off the engine, see DTC code for that.scan before ,during and after failuresand use the pending button too on t he scan tool as here may be marginal or intermittent failuresalso (Im no hybrid guru) but some hybrids do not run the engine (to save fuel) until the battery has some amount of discharge detected.some even have switches to set the mode you want,save fuel or save battery life, IDK this car.
2006 Lexus GX470. How to fix the out dated computer?
You can get a cheap scan tool on Amazon for $35. If you want to do it for free, you can disconnect the negative battery terminal for 15 minutes. After that though you will need to know the radio code and you will have to reset the security system.
How to remove a 06 Lexus is250 ECU and mainly the junction block mounted inside the case that sits above the ECU
- Locate the ECU: The ECU is typically mounted under the hood of the vehicle, near the firewall.
- Disconnect the battery: To avoid any electrical shock or damage, disconnect the negative battery cable before beginning the removal process.
- Remove the cover: There is likely a cover or panel that needs to be removed to access the ECU. This may be held in place with screws or clips.
- Disconnect the electrical connections: The ECU will have several electrical connections that need to be disconnected before it can be removed. These connections may include plugs, wiring harnesses, and other components.
- Remove the mounting screws: The ECU is usually mounted to the vehicle with screws. Remove these screws to release the ECU from the mounting bracket.
- Remove the ECU: Once the screws are removed, the ECU should come out relatively easily. It may need to be lifted out over the junction block or other components.
- Remove the junction block: The junction block is mounted above the ECU and may be held in place with screws or clips. Once the ECU has been removed, the junction block should be easy to access and remove.
Note: It's important to follow the steps carefully and to be cautious when removing electrical components from a vehicle. If you're not confident in your abilities, consider hiring a professional mechanic to remove the ECU and junction block for you.
Not finding what you are looking for?