Lexicon Logo

Lexicon Popular Questions, Answers, Tips & Manuals

Do you work here? Claim your company

  • 40 Products
  • 269 Answers
  • 39K Views

Call for warranty.

Lexicon RV-8... | 88 views | 0 helpful votes


Lexicon word challenge for PC free download. Microsoft Official Home Page

Lexicon... | 138 views | 0 helpful votes


The latest OS X is 10.13.3
Maybe the newer OS X would help.

Lexicon Lambda... | 59 views | 0 helpful votes


you SHOULD be able to.

Just use Direct Sound in the host tab.

Lexicon Music | 56 views | 1 helpful votes


Have you checked the cables, jacks, pan settings etc?
There may also be damage to the potentiometer.

Lexicon MX200... | 39 views | 0 helpful votes


you have to set a master and slave(s) devices, and ensure that all the timings (16/24 bit, the 44.1/44/96k) are consistent in all devices

Lexicon I ONIX... | 49 views | 0 helpful votes


Take it back to where you purchased it, they will help you.

Lexicon Alpha... | 35 views | 0 helpful votes


replace your hdmi cable between tv and preamp...lemme know if it works.

Lexicon Audio... | 160 views | 0 helpful votes


In my experience, reasons for seeing errors in VST System Link (VSL) are usually due to the digital signal path (audio and/or data) not being routed properly within the System Link dialog box. If for example, you're using s/pdif between two ASIO 2 compatible audio cards properly (OUT of card #1, to IN of card #2 - then OUT of card #2 back IN of card #1), you also have to set your s/pdif System Link I/O channels in the dialog box to the 'same' channel...If say your options are s/pdif channels 9 & 10 (or whatever they are), you set the I/O's of both computers VSL dialog boxes to either channel 9, or all to channel 10. You of course need to route your digital audio properly within your audio interface! (see your cards documentation on that).
You can test if it's routed properly by 'listening' to audio from each computer, from the other...meaning listen at computer 2, from computer 2 & visa-versa. If you hear the audio thhen it should be correct. But in order to 'hear' the audio (besides proper settings in the VSL dialog box) you must 'also' set those digital audio s/pdif channels within Cubase's VST Inputs/connections. But in 'this case', you use both channels 9 & 10 for your Inputs/Outputs. They also say it's best to place your VSL digital audio channels at the top of the Inputs/Outputs list.
You do not need to keep the s/pdif channels in the VST Inputs/connections to make System Link work however, that's if you need to 'listen' or if you need to test whether it's routed properly.
Getting VST System Link working can seem complicated at 1st, but once you understand, and have it working, you realize it's actually not that hard at all. I recommend taking notes, and writing down what you did to make it work, as you go along the way. That has come in very handy when I need to use it again. Also READ your PDF manual and follow that to the letter!

Lexicon Omega... | 134 views | 0 helpful votes


check the "buffer" setting - set to the lowest number possible. You can't eliminate the "latency" but you can reduce it a lot. Also 0 try to monitor what you are recording with "live" sound (input instead of output) - also, you may need to download a different driver for your audio card, try ASIO4ALL

Lexicon Alpha... | 56 views | 0 helpful votes


you have too much latency in your setup. Try using ASIO as your audio engine in your recording program. Also, shut down all unnecessary programs running on your computer to get better performance.

Lexicon Alpha... | 45 views | 0 helpful votes


Are there any labels on the fan?

Lexicon LX-7... | 246 views | 0 helpful votes


Are you trying to use the mic input on the back or plugging it into the instrument input on the front? If you use a low impedance mic with a quarter inch instrument input cord, you would need a transformer adapter to make the mic work on high impedance. Even if you put it on line in, you would still have to convert it. Only the XLR socket on the back will work on a low impedance mic.

Lexicon Alpha... | 164 views | 0 helpful votes


If unt was dropped, look for broken PC board in the vicinity of the rotary encoder. Also look at solder connections to make sure they are sound. A little contact cleaner applied to encoder through an opening so the spray gets inside will help clean contacts. If the knob itself is hard to turn, the shaft is likely bent, and there may be damage to the encoder itself.

Lexicon Mx200... | 233 views | 0 helpful votes


You will have to assign the i/o setting in your DAW's prefrences.

Lexicon I ONIX... | 596 views | 0 helpful votes


Hi
every driver related problem can be solved by using this software: Driver Update Software.
enjoy

Lexicon Lambda... | 2,877 views | 16 helpful votes


In my experience, reasons for seeing errors in VST System Link (VSL) are usually due to the digital signal path (audio and/or data) not being routed properly within the System Link dialog box. If for example, you're using s/pdif between two ASIO 2 compatible audio cards properly (OUT of card #1, to IN of card #2 - then OUT of card #2 back IN of card #1), you also have to set your s/pdif System Link I/O channels in the dialog box to the 'same' channel...If say your options are s/pdif channels 9 & 10 (or whatever they are), you set the I/O's of both computers VSL dialog boxes to either channel 9, or all to channel 10. You of course need to route your digital audio properly within your audio interface! (see your cards documentation on that).
You can test if it's routed properly by 'listening' to audio from each computer, from the other...meaning listen at computer 2, from computer 2 & visa-versa. If you hear the audio thhen it should be correct. But in order to 'hear' the audio (besides proper settings in the VSL dialog box) you must 'also' set those digital audio s/pdif channels within Cubase's VST Inputs/connections. But in 'this case', you use both channels 9 & 10 for your Inputs/Outputs. They also say it's best to place your VSL digital audio channels at the top of the Inputs/Outputs list.
You do not need to keep the s/pdif channels in the VST Inputs/connections to make System Link work however, that's if you need to 'listen' or if you need to test whether it's routed properly.
Getting VST System Link working can seem complicated at 1st, but once you understand, and have it working, you realize it's actually not that hard at all. I recommend taking notes, and writing down what you did to make it work, as you go along the way. That has come in very handy when I need to use it again. Also READ your PDF manual and follow that to the letter!

Lexicon Omega... | 783 views | 0 helpful votes


first thing to do is check your sound and audio settings, goto control pannel,then, sound/audio setings and see if everythings set up properly

Lexicon Lambda... | 192 views | 0 helpful votes


It MAY be waiting for an UPDATE of firmware via USB. In other words you may have triggered an update mode that it will not exit without sending an update. The second possibility that comes to mind is that one of the buttons or the switch behind it may be stuck which can lock up the processor. Look for a button stuck in or that feels un-normal.

Lexicon MX400 FX... | 281 views | 0 helpful votes


Read this procedure to possibly fix the remote:
http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12963989782821
They also sell replacement remotes.
Zoom in on the picture of the original remote provided on the site (or look at your own) and get the actual remote model number.

or check eBay: search for "(model of the device or the remote) remote", check the 'include description' box. Usually cheaper than the vendors.

Lexicon MC-1... | 99 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Lexicon Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

Tony Raia

Level 2 Expert

254 Answers

Marvin
Marvin

Level 3 Expert

84565 Answers

Are you a Lexicon Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...