Landice Recent Questions, Troubleshooting Help & Support

at starting, trys to go to speed and then reads LS on screen and runs very slow, with no response to any buttons.

ask here

Check wall outlet for power , then if outlet is good unplug unit remove motor shroud you will see a charcoal or white ceramic fuse check it if open replace blows again immediately you have a shorted lower board. Here is the info Landice they help you with parts and get you in touch with a servicer if you need one.

Landice, Inc.
111 Canfield Avenue
Randolph, New Jersey USA 07869
(800) LANDICE
(973) 927-9010 - FAX: (973) 927-0630
[email protected]

Depending if this is a L7 You must first go to the end of unit using 9/16" socket counterclockwise pull the bolts off now when doing this couter the rotation that is took for the bolts to come off write it down so when you are ready adjust tension you have a reference . Then proceed to remove the end plates (Phillips screws). Then where the foot plate is slide the plastic cover off and you will see screws holding the foot plate remove them and the plate will come off. Go back to the end and remove rear roller , now you will see first the felt washer these used to dampen noise when you are walking or running.Now you will be able to lift and slide out the broken deck and you will see the deck load washer and impact absorbers To replace them you can use an adjustable end wrench go under each absorber loosen lock nut. Also on the safe side I would inspect the running belt to see if the deck damaged it. Reverse disassembly procedure and start unit increase speed around 3.0 mph and adj belt tension 1/4" turn ( clock wise) at a time until belt is not slipping and to center belt.

The little hamster inside is either hungry or just plain lazy. Try sticking a stalk of celery with peanut butter on it just under the belt, if he doesn't grab it, it's a sure sign you've got yourself a lazy rodent. Shoot it and then call the 800 number in your owners manual immediately for a replacement. I'd insist on some celery too, there really is no excuse for unmotivated hamsters. Really.....ever seen em in those balls? How much did you pay for that treadmill? I rest my case.

Hi,

Please find the working manual for Landice l7. Check out page 6 onwards. It would explain how to assemble. Now if you try the opposite you can disassemble it as well.

http://www.landice.com/Media/CTManual.pdf

Please let me know if this does not help else please accept it.

Thank You for contacting Fixya.com

Hi


Thanks for using FixYa. While the line is on go to breaker box see what size breaker you are running, increase to a twenty amp. If a fridge or freezer is on same line, find a new outlet on another line. Although your 20 amp circuit should be able to handle the two loads - if the fridge compressor should happen to cycle at the same time you’re cranking away at the treadmill...the two motors combined in-rush currents together may be close to overload.

Generally (and in compliance with Code article 210.52)...the refrigerator should already have its own dedicated circuit. But - in older homes... (Wired back before the 2 small appliance circuits plus fridge circuit in kitchen requirements codes were in place) you often will find other receptacles on the same circuit as the fridge. So having a dedicated circuit for the fridge isn't because it's a big power draw...only because it's an essential item....and a circuit you want to maintain power to avoid spoilage. The Treadmill should have its own dedicated 20 amp circuit...as recommended in the specs for the unit. That's not to say you'll burn the house down if you continue to operate the circuit as it....just that you are pushing it to the max IF both motors happen to peak at the same time.


Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks

Rylee

Does your L7 have error code that looks like L5 , but its really LS which mean lost signal. Unplug unit take motor shroud off then plug unit back in wall outlet. When looking in front unit you will see a Motor control board and there are LED lit up one of them should be an amber light this is you speed sensor which is attached to the top of your motor. Manually rotate the fly wheel and see if that light flickers if it does then your speed sensor is working properly if not replace speed sensor. The next thing to look at is the motor brushes to if they are worn unplug unit you should see slitted caps on both side of motor remove them if they are less than 3/8" they need replacing. That for the most parts should take of your problem. Call Landice @ 1800-526-3423 have the serial# handy their on all the components in the unit

first screen shows any error number? for what you describe I think it is simply speed sensor, try to check the cables leading to the sensor card. and then checks whether the sensor is aligned correctly.
Check speed sensor alignment.
It should be within 1/16" of the flywheel
and parallel to the flywheel.
Is it out of position?

Hello CaptJack. Your treadmill is need of a major tuneup. Contact landice at http://landice.com/Pages/contact_home.html
They will be able to direct you to their nearest service center.....or you might ask them if they take turn-ins against rebuilt models........... Regards, Joe

This happened to mine and I figured out that the sensors were dirty. I got some canned air that you spray on computers and sprayed out the mother board. I also sprayed the electrical contacts with electrical contact cleaner and the treadmill is a good as new.

Hi,

There might be many reasons. Are you sure that the power is entering the Treadmill?

Might be a cable is not fine, Make sure there should not be any cut or burnt wire.Second might be upper control board went bad. In this case, you need to call professional on site or check that and if faulty replace it.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

your belt adjuters are behind and hidden in the toe kick
open that up you will see a nut on both sides on the belt
make sure you tighten both the exact same or your belt will slide off to the "lower" side

Not sure how long or often this is used, but you may just have to do a maintance on it. In your manual it will show you but all it sounds like is the tracks need cleaned and oiled. The slowing down will show up at slower speeds first due to the fact that the motor is not turning as fast and will feel the drag of dry or dirty tracks. When you are going faster this will not be noticed as much since the motor is spinning faster it will over come slight resistance. So try cleaning and oiling the tracks as per your manual and your problems should be solved. You may also have to adjust the tension on the belt

hi i get this prob a lot on peugoet 406
its the ignition worn, try wiggle the key when running and it should work if not get back to me.

I found two bolts at the rear of the treadmill that extended toward the tension bar. I felt they were the only way to adjust it. I had been too nervous to try and move them, but that is what did the trick. Thanks

You may want to take off you head board and check all the connection. this is not hard to do. Also when you in there check you cable connection. can you do this? I’m happy to help further over the phone at https://www.6ya.com/expert/howard_079189dd4959a511

the e1 symbol is an engineering error code for an electronics malfunction (actually is senses the motor not turning and giving an error. The most likely cause is the motor control board
www.twincityrepair.com

is it still covered by warranty?