La Crosse Watches - Page 5 - Recent Questions, Troubleshooting & Support

When you change the battery on this watch you have to short the circuit board. You need a fine pair of tweezers and you need to look on the circuit board for an arrow or bare spot, put 1 end of the tweezers on that place on the circuit board and the other on the battery at the same time. that should do the trick if the battery was installed correctly and the battery is good.

How do I reset watch after changing battery?

Downloaded instructions and working on it.

Thank you.

Bernard W. Goering

Alhamdulillah, the problem solved (at last) tks to IRONMAN (http://www.fixya.com/support/t579677-instructions_mens_festina_watch_16095#SameProblemContinued)

The steps are like this :
1. Pull the crown full, and turn it clockwise until you find the right day.
2. and then push it one click (dont push it to hard so it back to normal position) and turn the crown counter clockwise to adjust date.
3. Push the small button near the crown to adjust month.

and voila... the problem solve

pull the dial out half way, and turn it forward to adjust the day, and dial it backward to adjust the date.

I've just worked it out! Change month....depress inset button on side above hand winder. One push with cocktail stick or similar will advance month. Change date.....pull out hand winder half way, turn knob anti-clockwise until desired number is met. Change day...... pull out hand winder fully, turn clockwise passing midnight repeatedly until day is set, continue to set time, keeping an eye on 24 hour display for am/pm.
All the best, Bob

altitude changes depending on pressure; because you are along ocean, you experience it more than usual.
M problem is that temperature remains higher than normal one (30°C), can you solve it ?

you can get the instruction manual from this page
http://www.radiocontrolledclock.com/latewacl.html

Go to this site below and print out the manual. It gives their recommended way of doing it. If that doesn't work, it even gives a phone number to call and email address to write to..

http://www.lacrossetechnology.com/967s/manual.pdf

This watch automatically sets itself. I you live in the eastern time zone, you just have to wait for the watch to receive the signal then it will set itself to the correct time & date. The signal is strongest at night between the hours of 10:00 pm & 2:00 am so it normally takes over night to set. Sometimes the weather interferes with the signal so I tell people to give them a couple of days to pick up. Also if you are having trouble receiving the signal try placing the watch by a window. If you do not live in the eastern time zone try these instructions:

Hold down the button for 2 seconds until the time zone abbreviation & zone flash the keep pressing the button until your correct time zone is displayed. Then wait about 8 seconds for the watch to return to normal display. Then you just have to wait until it picks up the signal & sets itself. I hope this helps.

If you are not familiar with battery replacement and do not want to do it yourself, then nearest jeweller or watchmaker shop will do it for you.
If you wanna try it yourself, ask me questions and I'll guide you how to.

Solved it! La Crosse let you download manuals from their website.

Check this website I think it will help you with your peoblem If not post it again and I'll try and find some other help http://www.geocities.com/gregclep/clocks/lcwatch.html

Here is the link to the user manual if you need it; http://www.lacrossetechnology.com/k2100/manual.pdf Page 12 gives you contact details for lacrosse support or use; http://www.lacrossetechnology.com/support/contact.php Hope this helps, please ask again if not and i can hopefully find you another source :)

Here is the link to the user manual for this watch if you need it; http://www.lacrossetechnology.com/k2100/manual.pdf page 12 gives you all the contact details for lacrosse. I couldnt find the info online to be sure, but some of these watches do have a separate pressure sensor for altitude and barometric pressure, and sometimes the path to one could get blocked or it could become faulty. I would contact la crosse and find a dealer to get the watch serviced, you could probably do it yourself but you need to get replacement seals from them anyway (these are important). ask them to check if the sensor is clogged, it happens sometimes. Hope this helps :)

Here is the form used to contact lacrosse for a watchband; http://www.lacrossetechnology.com/watchband_form.pdf or you can use; http://www.lacrossetechnology.com/support/contact.php Here is the user guide for your watch if you need it; http://www.lacrossetechnology.com/k2100/manual.pdf Hope this helps :)

Si porque tengo este reloj

how do you set the time on the digital george watches?