Can you maually adjust the hour hand on the la crosse WT-3161BL IT'S SLIGHTY OFF
Unfortunately the only way I know of synchronizing the hands is to remove the glass. I am assuming your clock has a plastic glass which is held in by 3 knibs which protrude into the case. Examine the edge of the glass and locate one of the knibs, with a small screwdriver gently but firmly push this knib in and pull the glass up to release it. Once out you can position all the hands at exactly 12 o'clock by pushing them gently (don't take them off). Replace the glass and your done!www.serendipity-gifts.co.uk)
Www.lacrossetechnology.com/8248 need to reset time!
I'm not totally sure what you mean by "reset the time" because the unit normally sets the time automatically from the WWVB radio time signal. If you want to do it manually, this is what the
Instruction Manual (PDF format) says:
MANUAL TIME SETTINGIn case the atomic clock is not able to detect the WWVB-signal (disturbances, transmitting distance, etc.), the time can be manually set. The clock will then work as a normal Quartz clock.
- The hour digits will start flashing in the upper LCD.
- Select the desired hours by pressing and releasing the + key.
- Press and release the SET key to advance to the minutes setting.
- Now the minute digits will start flashing.
- Select the desired minutes by pressing and releasing the + key. If the + key is held, the unitswill increase by 5.
- Press and release the SET key to confirm the Time setting and continue to the Year setting.
Sensor remote does not send
After some time outside, corrosion occurs on the circuit board, when water enters the unit through the vent on the front of the sensor. The vent should not be blocked, as this will still result in corrosion due to condensation building up in the sensor. Corrosion will be less likely to occur, if the sensor is located away sources of humidity and falling water. I located mine in the shade on my deck, under an upsidedown flower pot.
10/7/2012 5:15:51 PM •
La Crosse...
•
Answered
on Oct 07, 2012
•
2,212 views
Need to reset atomic clock to Virginia time zone; now 4 hours ahead
To set up your clock simply install one fresh AA, LR6 ALKALINE battery. Due to the nature of long wave radio signals it is normally not possible to receive a signal during the day so it is best to install the battery late in the evening. Select your time zone by pressing one of the four time zone buttons PT-Pacific Time, MT-Mountain Time, CT-Central Time, ET-Eastern Time. The time zone buttons may be pressed any time after installing the batteries. If multiple buttons are pressed the clock will set to the time zone selected last. If no time zone is selected the clock will default to Pacific Time. Another time zone can be selected during or after the clock has set itself. Your clock can only set itself to one of the four time zones stated above. For time zones outside of PT, MT, CT or ET you must manually set the time using the Manual Time set button on the back of the movement.When the battery is installed the second hand will advance eight seconds (two seconds per step x four steps). The clock is now searching for a signal. For the initial setting it is recommended to stand the clock in an upright position near a window. Within five minutes the clock will either receive the WWVB signal and set itself to the exact time, or it will determine that the signal is not receivable at its current location and time of day. If a signal is not receivable it will fast-forward the hands to the 4, 8, or 12 o'clock position and search for WWVB eachhour until a signal is received. If the time is manually set the clock will continue to periodically search for a signal and automatically reset the hands when the signal is received.
Need instruction manual for equity wireless thermometer
Hi George,I believe your Equity wireless thermometer is manufactured by LaCrosse Technology. Here is a link to their website:http://www.lacrossetechnology.com/From this page, you can search the type of wireless thermometer or weather station you're trying to use. (You didn't specify a model number in your request).Also notice that there is link on that page for Support; clicking that will take you to the Manuals link. You will need to find your proper model number in the drop-down menu.Also, there is a Contact link, so you can contact them directly for further assistance if you are unable to find your model's information.Good luck, George! Hope this helps!
2/11/2012 4:38:27 PM •
La Crosse...
•
Answered
on Feb 11, 2012
•
964 views
Not finding what you are looking for?
good about getting customers owners manuals. .
