La Crosse Audio Players & Recorders - Popular Questions, Answers, Tips & Manuals

https://www.lacrossetechnology.com/support/manuals.php 3N6 its the technology named , but the model you can choose can be find on this site . Mabe the model and page are find on these pictures. la crosse 3n6 Google zoeken

I've had this clock for a year now. The projection light will no ...

www.amazon.com/clock-projection-light.../1?_... Amazon.com, Inc.Sep 13, 2013 - The projection light will no longer stay permanently on - it used to. ... if it during the day you can't see the projection because of ambient light. Questions And Answers: does the projection light stay on 24 ... Jan 7, 2014 Amazon.com: Questions and Answers: Oregon Scientific RM313PNA ... Jul 19, 2013 More results from www.amazon.com

would like to set the correct time

YES! I also have the same issue - I ASSUMED that it was the RED LASER BLINKING behind the PROJECTED time (on the wall/ceiling), but a different brand with a similar problem was described as actually a PROJECTED RED LED, NOT A LASER. In either case, still not sure what the problem is. ;( To RESTATE the ISSUE for NEW READERS: These digital alarm clocks (with AutoSet through radio signals) project the time in red color on the wall or ceiling. HOWEVER, after some time, the PROJECTED RED TIME begins to flash or blink INTERMITTENTLY - this is NOT a setting issue. The flashing/blinking projection is totally intermittent, occurring every 0.5 to 6 seconds, randomly, leading me to believe it COULD be broken/cracked soldering contact points (which presumably could be fixed by resoldering those contact points on the circuit board), OR perhaps some issue with the internal chip (which would NOT be fixable by a DIYer, I would assume). ANY THOUGHTS?? Thanks!

http://www.lacrossetechnology.com/5110/manual.pdf

http://www.klockit.com/pdfs/87214.pdf

It sets itself eventually from the source in Colarado. You just choose the Time Zone.

This manual should work for you.

http://www.klockit.com/pdfs/87214.pdf

Hello
I've the manual you need; for La Crosse WT5110 radio controlled projection alrarm clock. But I can'e send it to by this site, as it does not allow me to send such a large file. If you send me your email address by Fixya, I'll send it to you by return mail. OK.

This link goes to downloadable instructions for many LaCrosse clocks. One should work for you.

You might find it and links to the manual here.

http://www.klockit.com/depts/AtomicClocks/dept-52.html

Strangely, the lacorss site itself downs't have a link to the manuals.

Go figure.

http://www.lacrosse-clock.com/lacrossetechnologyatlacrosseclock.htm

Instructions...

you have to release the Mode/Min button after 3 seconds.

http://www.klockit.com/pdfs/87214.pdf

"TIME ZONE SETTING

1. Hold down the "MODE/MIN" button for 3 seconds, the time will flash in the Time LCD.

2. Press and release the "SNOOZE" button to advance to the time zone selection.
3. In the indoor temperature/humidity section of the LCD the time zone will flash."

low temperature/low humidity (LL)

if it is wireless then check the sender unit
check the battery

severe cold weather can be hard on batteries

Did you try adjusting the time manually? Did you adjust the time zone/ city setting on them as well? If you need further assistance give me the exact model and i can assist you further.
Thank you,
Lee

To turn off alarm press ALM1 button for a second.
For time follow instructions here
http://www.lacrossetechnology.com/5432twc/manual.pdf

I found my manual so it is up and running again. Thanks

No, this model does not have a light or backlight. Feel free to peruse the manual information at your convenience though, and I do hope I've helped!

WT 2171U manual

1) Does the remote have batteries? See other posts that describe how to do this (4 screws in back need to be removed). Temperature should be displayed in small window of the sending unit if it's working.
2) Hold Channel button for 3 seconds until it beeps - the unit then searches for a signal.

I suggest you hit the "reset" button - THEN immediately set YOUR local time zone (I'm assuming you're in Pacific time zone and it defaults to Eastern. So SET ZONE right after you RESET the unit. At 3 or 5 in the morning it should do a complete update for you. There is also a little "Antenna" icon on the unit - you should see that with several 'waves' if you've got a good signal. Also, put the radio/clock on the side of your house that most closely faces Denver, Colorado. Try those and let me know how it goes for you. Thanks,
Johnny