Kyocera Recent Questions, Troubleshooting Help & Support

First you have to upgrade the firmware to the latest. If the error code appears again, then you have to replace the main pwb assy (controller).

office 365 uses protocol TLS 1.2 since October 15th and I think you Kyocera is using TLS 1.0 or TLS 1.1 which Microsoft has stopped using due to vulnerabilities in the protocol. see https://www.loffler.com/blog/will-your-office-mfd-work-with-office-365-security-updates Check if Kyocera can use TLS 1.2 https://sites.google.com/view/howtoguidesforkyoceraprinters/the-command-center-rx/security-settings/network-security otherwise contact Kyocera support and see if they have an update that allows TLS 1.2 on your device.

nesesitas give more information, but the problem is in the main charge corona, replaces the charging wire crown,

https://printcopy.info/?mod=erc&brand=Kyocera&model=TASKalfa+6500i&page=17 Either defective fuser OR defective engine. Replacement of one or the other is the fix. Check warranty or service contract. Sadly, you will have to decide if the repair costs more than replacement of the printer. https://www.kyoceradocumentsolutions.us/en/support/downloads.name-L3VzL2VuL21mcC9UQVNLQUxGQTM1NTNDSQ==.html

It Kyocera to go in service mode is press 1,0,8,7 again 1,0,8,7.simple like this.

What is this main pwb and operation pwb

This might take some doing reseting the fs 1118 but it can be done if the fuser only got hit by a powersurge or overheated due to paperjam by the fuser...

press system menu/counter
select service settings via up and down cursor keys

now while pressing start key and # key press enter

then select maintenance mode by using the up down cursor key

press enter

enter 163 and then restart the copier...

sometimes you wont even be able to get to the service mode...

open the front of the copier and then execute the steps... the front meaning the area where you the toner is located...

trying keeping it open and do the steps...

if that fails then open it take out the toner drum cartridge and then put it back in...

then do the steps...

if it still doesn't take try it a couple more times...

if it still doesn't take.. buy a new fuser...

but it should take... it just takes a little experimentation... I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

Email me @[email protected] for any type of firmware you need

https://www.fixya.com/support/t15938498-get_into_service_mode_kyocera_copier

change printer emulation to KPDL-Auto

example

take the cartridge along to a ink refiller shop and ask them as they have a good knowledge of product inchangeability

check the bypass transport connector for a small piece of paper. or the paper sensor arm is jammed down there are 2 one in the transport unit and one in the mp tray

Update its firmware or open the control panel buttons and you clean them well

Try turning it on and off, that should stop the beep.

I need to know how to clear this error code C6950 for TASKalfa 3551ci KYOCERA. Thank you

You need to contact a Kyocera repair service on this problem, have them come out to service the machine.

Defective developing humidity sensor or poor contact insertion connector problem try to clean the connector but before doing all this first empty the Dev Unit clean it well the insert it back into the machine and start the equipment.

Enter service mode 1087twice key pad in 935 the you follow these steps Setting 1. Press the start key. 2. Select the item. Initial setting: MODE0 3. Press the start key. The setting is set. 4. Turn the main power switch off and on. Supplement After removing the cause of the problem, be sure to change the setting in OFF.