Kyocera Office Equipment & Supplies - Page 3 - Recent Questions, Troubleshooting & Support

Error code 08 on a Kyocera FS-1020MFP printer typically indicates a problem with the printer's firmware or hardware. Here are some steps you can try to resolve the error:

1. Restart the printer: Turn off the printer and unplug it from the power source. Wait a few minutes, then plug it back in and turn it on.
2. Check the connections: Make sure all cables and connections to the printer are secure and properly connected.
3. Update the firmware: Check if there is a firmware update available for your Kyocera FS-1020MFP printer. Updating the firmware may resolve the error.
4. Reset the printer: Perform a hard reset on the printer by unplugging it from the power source, waiting a few minutes, then plugging it back in and turning it on.
5. Contact Kyocera support: If the error persists after trying these steps, contact Kyocera support for further assistance. They may be able to diagnose and resolve the issue.

Note: These steps are general suggestions and may vary depending on the specific m

Error code 08 in a Kyocera FS-1020MFP printer is a communication error and can be resolved by trying the following steps:

1. Check the cable connections: Make sure that the cable connections between the printer and computer are secure and properly connected.
2. Restart the printer: Turn off the printer and then turn it back on. This can often resolve communication errors.
3. Try a different cable: If the error persists, try using a different cable to connect the printer to the computer.
4. Update the printer driver: Make sure that you have the latest printer driver installed on your computer. You can download the latest driver from the Kyocera website.
5. Reset the printer: Perform a reset on the printer by unplugging it from the power source for a few minutes and then plugging it back in.
6. Check the computer's firewall settings: If the error persists, check the firewall settings on your computer to make sure that it is not blocking communication with the printer.
7. Contact Kyocera support: If the error continues to persist, contact Kyocera support for further assistance. They will be able to provide more specific guidance for resolving the error.

J11 has come when the resistance unit sensor liver is open or any paper jam here. if no paper jam here my be sensor damage.

If only the Energy Saver (or Power) button lits and the rest of machine is off, then you probably need a new power supply (LVU).

contact me my number 0092 345 5764775 0333 8014741 i work know kyocera canon ricoh xerox

The problem of image fading in some lines on a Kyocera3050 printer could be caused by several factors. Here are a few troubleshooting steps that can be taken to resolve the issue:

1. Check the toner level: Make sure that the toner cartridge is properly installed and that there is enough toner in it. Low toner levels can cause image fading or streaking.
2. Clean the printer: Clean the drum unit, the corona wire, and the primary charge roller. Dust and debris can accumulate on these parts, which can cause image fading.
3. Check the drum unit: Make sure that the drum unit is properly installed and that there are no signs of damage or wear. If the drum unit is damaged, it will need to be replaced.
4. Check the corona wire: Make sure that the corona wire is clean and free of debris. If the corona wire is dirty, it can cause image fading. Clean the corona wire with a lint-free cloth or a foam swab.
5. Check the primary charge roller: Make sure that the primary charge roller is clean and free of debris. If the primary charge roller is dirty, it can cause image fading. Clean the primary charge roller with a lint-free cloth or a foam swab.
6. Check the fuser: Make sure that the fuser is properly installed and that there are no signs of damage or wear. If the fuser is damaged, it will need to be replaced.

If after trying the above steps, the problem persists, it's recommended to contact the manufacturer for further assistance or to contact a professional technician for repair.

1. Check the cover switch: Make sure that the cover switch is securely in place and that it's not loose or damaged.
2. Clean the cover switch: Use a clean, dry cloth to wipe down the cover switch. Make sure to remove any dust or debris that may have accumulated on the switch.
3. Check the control board: Make sure that the control board is securely connected and that it's not loose or damaged.
4. Update the firmware: Make sure that your printer has the latest firmware update. Firmware updates may include bug fixes or improvements that can resolve unexpected shutdown issues.
5. Check for any jammed paper: Make sure that there's no paper jammed inside the printer. If you find any jammed paper, remove it carefully.

there is a black tab in the center where the papers come out that is the tray full sensor arm that is more then likely stuck

The drum is not pushed fully into the machine.Open the waste toner container door and gently push all units into the printer.Then turn off the printer at the wall.When you power back up the printer should be back to normal.

Restart the machine

this code is saying you have a bad yellow dv unit you have to have a new 1

There is a cleaner system that is supposed to pick up leaking toner from the cartridge. Try cleaning the toner contacts on the machine and also on the toner cartridge itself. Use metal polish and then an alcohol swab. If that doesn't work, call for service. I had similar on a commercial machine and it needed a part. https://www.google.com/search?q=Kyocera+Ecosys+M6235cidn+prints+blue+speckles ..

Scan to email issue. You have to go deep into advanced settings to get this right as stipulated by your mail provider. https://www.google.com/search?q=0x1101+Error+code+smtp+server ..

One of the Common error for (Papper Jam) in printer is Error 0x000003eb. Error code 0x000003eb indicated printer connectivity or printer installation error. If you are trying to install a printer driver but keep getting Error 0x000003eb prompted, make sure you have logged in as the administrator of the computer and then try installing the driver. If the problem still happens, try the below solution steps to solve this problem. The error message doesn't give you much information as it just says unable to install the printer and gives you the error code 0x000003eb. The Error Message shows you: "Unable to install a printer. Operation could not be completed (error 0x000003eb)" The printer connectivity or installation error 0x000003eb occurs because the drivers are somehow got corrupted or incompatible. We know the printer is a very important part of our day to day life. We all need a printer to get hard copies of our important files and documents within a few minutes.

Toner Sensor K (black) problem. Probably defective developer unit K

Check/replace the toner.

Hi if your printer has a nozzle head, please clean that first. You should also check that you ink cartridges are not third party. If so, please switch to kyocera brand. Thank you.

Hi, please restart both your printer and the source that you're printing from (ie computer) before trying to print again. Also, please attempt to use another flash drive to print to the printer as well. If possible, you can update the firmware of your printer to make sure that everything is updated on the machine. Thank you.

This happens when the machine knows that you are using counterfeit or refilled toner cartridges. Or your toner refiller gave you an empty one, or one with a teaspoon of toner powder in it.