Kuppersbusch Answered Questions & Fixed Issues

SAve my life! Thank you so much!

It doesn't appear to be a known issue. The fault is likely a faulty Thermistor which is a temperature sensor that feeds information to the control board. https://www.google.com/search?q=Kuppersbusch+EEB+6600.0+not+maintaining+temperature ..

It is a little known make in North America and no one has documented the job. If you can see the sensor, you can replace it. Just follow the wire, they usually hide in the back or behind the control panel. This looks like the part marked as 'thermometer' and is actually a 'thermistor', an electronic temperature sensor. https://shop.euras.com/de_de/hausgeraete-dresden/K%C3%9CPPERSBUSCH_EEB98000MX76_701416_D338878.html Looks German, this link might work better for you based on your location. https://www.google.com/search?q=Kueppersbusch+EEB98000MX76+replace+oven+sensor ..

Just so you are clear, we are FIXYA dot com, we aren't them, we just have a category for handy filing. You have an appliance in a country with no support. https://www.home-kueppersbusch.com/ Germany or UK I reckon, but easiest just to ask them direct. https://www.google.com/search?q=EEB+9800.0+MX+thermostat ..

If the brew unit of your Kuppersbusch EKV 6600 coffee machine is not moving onto the limit switches, even though the motor is driving, it could be a problem with the limit switches or the wiring connecting them to the control board. Here are a few steps you can try to resolve the issue:

1. Check the limit switches: Make sure that the limit switches are clean and free from any obstructions. If the switches are dirty or obstructed, clean them or remove the obstruction.
2. Check the wiring: Make sure that the wiring connecting the limit switches to the control board is securely connected and free from any damage or breaks. If the wiring is damaged or broken, replace it.
3. Check the control board: If the wiring and limit switches are in good condition, there may be an issue with the control board. If you're comfortable with electronics and have experience working with control boards, you can try to diagnose and repair the issue. If not, it's best to seek the help of a professional repair service

Full make and model are useful in such questions. Answer deleted.

You have an error in one of the temperature probes.

possibly bad door seal

Elements/customer service/check utube

Are you sure it is properly wired? For 1 phase 230v: 1= power earth 2-3 intersected = N 4-5-6 are L1-L2-L3 that should be conected together to L Kuppersbusch is not very cooperative about what their error codes indicate, but E6 seems to be a (low) voltage issue, so you might too check the cabling to the outlet, measure the voltage with a multimeter when you successively switch on elements

IN B.C. 30 INCH

there is a site on the net that handles teka and kuppersbrusch phone 1300-912-953 and is called appliancesalesdirect.com.au It is a long shot but they may be able to advise who will handle your problem

That could happen if the pans are not compatable with the unit.

Hello, Make sure the oven is warm, not hot. Open the door and spray the glass with vinegar and water and wipe with newspaper.

Take the middle filter out look into the bottom of the washer and check the impeller on the pump is free IE could be something like a rubber band fouling it.

http://kitchen.manualsonline.com/manuals/mfg/kuppersbusch_usa/kuppersbusch_usa_oven_product_list.html

Try turning off the power for a short while to allow the p c board to re set itself turn it back on and individually turn on each elements for a few minutes. Good luck Ray

might be transformer noise? try turning the cooktop circuit off at the electrical main switchboard.or get your wife to stop singing opera!!

could be a blown fuse, or the thermostat is stuck

go to www.repairclinic.com and get itGod bless you