Kuppersbusch Recent Questions, Troubleshooting Help & Support

The problem is hard water. www.dishwasherfilter.com has a product to solve this problem once and for all. It filters the water going into your dishwasher and removes the hard minerals that leave those spots. It is very affordable and even has a money back guarantee. You will love the way your dishes look with this product.

In this case it seems that the freezer had FROST formation on the drain tray or there is block on the tubing to the drain tank with a possible auto defrost malfunction. to confirm let us shut off the fridge and leave it powered off while you clean and check the evaporator for frost.
Now after about 6 hours plug in the fridge to start. Observe cooling to happen in about one hour and ice to from under three hours.
Earlier make sure that the thermostat was set to normal mode for freezer and fridge.
However if ice forms in the freezer then observe the fridge for about 24 hours for cooling to continue and the fridge to cut off . If not the auto defrost timer, or the thermostat must be checked. Frost formation without defrosting could block the air flow and so shut the air passage to the fridge.The blower fan must work continuously and if this is not working then the fan can be faulty. Also a fault on the control unit is a suspect to non functioning of any one of these components.
If defrost timer works but frost keeps forming check while the compressor shuts if the heaters are working, check continuity of the heaters.
There must be no residual water on the tray as it MUST drain off , if so check for any alignment or flow problems.Also test using a multi-meter on the defrost timer and the thermostat and make your observations so that we come to the solution.

Please check the link below for tips to remove the panels/parts:

http://www.espares.co.uk/advice/fridges-and-freezers/a/2

Hi,

According to you, this error indicates the water meter does not transmit any impulses to the control unit. So that the drinks will be dispense after 60 seconds. Press the coffee button again in order to stop the dispensing procedure before this time. Open and close the panel flap. The control unit will repeat the starting up procedure of the machine.

You may need to clean the water tank. So first clean it. Then pour only clean water and set the tank properly and reboot the machine. It will solve your problem.

Your oven is a convection one: the heat from the electrical resistances, depending on the exact model, is spread around in the oven by direct radiation or by the air moved by a fan. In either case some heat will always leak out.
But if the heat radiated outside the oven is really high then the ones that have installed it haven't put the correct insulation - either they put too little or (most likely) the forgot it completely.
Unless the heat is high enough to burn the stuff in the drawers it's not a problem, it's just that the oven will have to work a lot harder than it should have to heat the food. To fix that the oven will have to be taken out and an extra layer of insulation added around it - a simple one hour job.

we had the same problem....there is a bolt on the back side of the tray that pushes on a microswitch when you slide the tray back in; if aligned you can here the switch click. Otherwise it is just slidding by and missing....so bend the bolt slightly (ours had to go to the right as you look at the machine) and see/listen as to whether the switch is tripped. listen carefully; try just tripping it with a small probe to see if you can hear and feel the switch inside. good luck

The on switch to the burner sounds like its stuck open. See if you can shut it off at the switch or you will have to replace switch. If it stays on you risk fire so if you cant shut it off at the switch disconnect power to unit and call appliance technician for help.

If you have any further question please feel free to comment me back.

refer to the programming steps in the operation manual. It allows you to adjust the volumn of water for each setting.

HI. Does wire has color coding.With regard to the repair made.what is the name of the IC that seems to have the problem,did any IC,s has been replaced or it was just fix that seems no problem on it.There aree times that ic problem will just repeat because it has not been replaced .if wire has color coding on it.follow the color coding.how any wires do you have and as well as the pin in the connector.

A defective sensor will paralyze the operation of the controller and in your case, your unit will not resume its normal operation unless the thermostat sensor is replaced with a good one.
Visit http://www.kupperbuschusa.com, you will be able to find there the nearest authorized parts and service dealer on your area.