Konica Minolta Logo

Konica Minolta Popular Questions, Answers, Tips & Manuals

Do you work here? Claim your company

  • 786 Products
  • 78K Answers
  • 2M Views

I don't understand.

When you change developer.You want clear in service mode.(Counter)

Konica Minolta... | 2,053 views | 1 helpful votes


Use this function to initialize protect passcode and administrator's password.
1. Press <Mode>, <*>, <6>, <1>.
2. Press either [Initialize Protect Code] or [Initialize Admin Password].
3. Press [Yes].

Press <Mode> about two seconds until you hear the beep twice.
When you press " * ", you will hear short beeps.

Konica Minolta... | 245 views | 0 helpful votes


You have a problem with the HDD (Hard Drive) Main Memory Stick or the extra one if installed or worse case the Multi Function board. Have tech come out

Konica Minolta... | 125 views | 0 helpful votes


reload the print drivers

Konica Minolta... | 54 views | 0 helpful votes


Tri-folder motor malfunction. or bad motor

Konica Minolta... | 99 views | 0 helpful votes


Is the problem from adf?

Konica Minolta... | 38 views | 0 helpful votes


you found the right place right time buddy.. i know a lot of websites for repairs and manuals that can really help u..

Konica Minolta... | 35 views | 0 helpful votes


Service mode
System2
Costomers

Konica Minolta... | 34 views | 0 helpful votes


Remove the yellow drum, while looking at the yellow magnetic roller just below you will see a small Chrome looking section near the front of the unit where the drum was on the chrome is a small square where the drum density sensor is clean it out with air, if that does not work, then swap it with a different color and see if the code changes to that drum. wire connector for that senor is in the front.

Konica Minolta... | 47 views | 1 helpful votes


If it got jammed in the fuser unit (the hot part) the fuser can come out as a unit then remove the media wad

Konica Minolta... | 30 views | 0 helpful votes


The amount of toner in the developer too much toner.

Konica Minolta... | 22 views | 0 helpful votes


Most likely you received this message after a toner was replaced. Reseat the cartridge and restart the printer. If that doesn't work remove all of the toner cartridges manually and reinstall. Turn off the printer and open the top cover. Follow the toner cartridge all the way to the right side of the printer (on the white part). You should see a hole that looks like a cross. Take a pen or key and push down on the black button in that hole. While you are holding it down rotate the toner cartridge towards you. You want to get the colored roller on the cartridge about 1/2in away from the metal bar that says "consumable reorder". You should be in a position to take out the toner. Let go of the hole and remove the cartridge. Repeat the steps until all of the cartridges have been removed. Turn the printer back on at this point. You are going to get toner not installed messages on the printer. Open the top cover and the cyan tray will be in place. Shake the toner and install. Close the cover and let it cycle to the next color (black). Repeat the process until all cartridges are installed. If you are still getting the error you either have a bad cartridge or the carousel that the toners sit in is damaged.

Konica Minolta... | 25 views | 0 helpful votes


Where are you.
You can email me.
sklanarong@hotmail.com

Konica Minolta... | 35 views | 0 helpful votes


Clear the same way you accidently cleared the M2 except select web counter assumimg you replaced the web roller in the fuser unit

Konica Minolta... | 35 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Konica Minolta Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Steven Wander
Steven Wander

Level 3 Expert

594 Answers

Damen Wong
Damen Wong

Level 3 Expert

1950 Answers

Are you a Konica Minolta Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...