KLH Answered Questions & Fixed Issues

Yes... At best it may be just a loose mechanical fixing component or foriegn object :)

You should have its remote control to select the inputs. If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one. To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability? Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have. Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check this site too. http://remotesearch.blogspot.com/ Type in the brand name of your device in the search box, and press "Enter". Universal remote controls are available at most of the electronic spare part selling shops.

hi there try this link they can help you http://www.telefunken.com/service/

The mech binds up for age and lube hardening. Take it apart clean and relube it or have a pro like me do it for you. Larry 916-362-8708

If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Pull up older posts. Surf the site with patience. Do a search by type in the brand name of your device at its search box and press "Enter". http://electronicshelponline.blogspot.com/ Unlock procedure to many popular brand TVs are given.

Find the "Sub Out" connector on your TV. Likely an RCA jack. Run a cable from the TV to the Sub's Input and you're done. If your TV doesn't have a Sub Out then you might be out of luck.

The TV is locked by anyway. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy. http://electronicshelponline.blogspot.com/

what kind of speakers do you have hooked up? make sure your cables from the speakers are good. you should have an RCA type hookup on your record player, make sure they are in there good too

I do not own a blue ray player but my son has a PS3. The thick cable is most likely HDMI and it should work without the red/white sound cable...try unplugging them so the auto detect feature if available and activated is not trying to compete by finding 2 sources. If that works great! If not, you can get a yellow RCA for the video and just use those as a source - again, don't use the HDMI cable and try it. If you don't have a yellow RCA, I've used another red or white for video testing to see if I can get a video feed. Most newer red/white cable will pass a video signal just fine and are only color coded for ease of hookup.

What sort of tv do you have?

It depends. It either a Digital Coax cable(looks like an RCA cable), or it an Optical cable. The two look nothing alike.

It could be just a lead, check your lead heads and inserts are clean. Check along your leads and wires for any obvious kinks / tight bends / cuts / nicks / something sitting down on it or any damage to the wires. It could be there is another electrical device nearby interfering at a electromagnetic level. It could be just the dials / knobs need taking off and cleaning in behind. the pickups, you may not need to remove them just spray with electronic cleaner this stuff is great for lots of different electrical cleaning problems. Good luck

contact nearest TV repair centre.

Hi there! My name is Kimberly and I form part of the Social Media Department with DISH. It is my pleasure to assist you today and provide you with information that may be helpful to you. Where you trying to address the remote to the TV or a different device? With the *desired equipment* on, press and hold the *desired mode* mode button (about six seconds) on the top of the remote until all mode buttons light up, then release. Press 0-TV/1-VCR/DVD/2-Other, then press STAR Press the Up arrow button once per second while pointing the remote at the *equipment*. If the code for it comes up, the equipment power off. When it does, press the POUND button. If the code entered is valid for the remote, the mode light will flash three times. To verify the code works try several different functions for that equipment.If you have additional questions visit http://www.mydish.com/support/program-to-tv-scan-non-basic?WT.svl=leftnav or contact me directly at: [email protected] Media RepresentativeDISH L.L.C

i need a manual I need one sent to me

If it has a 3 prong plug, try a 3 prong adaptor - where only 2 prongs are plugged in. Sub's should not be grounded. If it still makes a hum noise, the amp circuitry may be compromised. Replace the amp with an equal at www.partsexpress.com If you need further help, I’m available over the phone at https://www.6ya.com/expert/dan_77d17b8918f54455

false contacts on the plate

No more likely the fuse would blow because of the diode! Fuses blow when there's an overload. These are general caused by semi-conductor device such as a transistor or diode that starts acting like it's just a piece of wire. Or as engineers call them short-circuits.

What about this 6.3 amp 250 volt fuse?

need user guide for KLH CDR-2000