KLH Logo

KLH Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 109 Products
  • 692 Answers
  • 111K Views

Wrap a wire around the outside Metal of your rca jack in back of your radio and ground the other end of that wire to the back of your radio and the noise goes away

KLH Audio... | Answered on May 09, 2015


Search the web , there are countless sites. Try ebay.

KLH R3100... | Answered on Apr 17, 2015


Go back into the set up and factory set it then go back through the end user set up again. Sony bipass code is 7774 for parental control Not sure where that 1s made. That dont work track down the customer service number for the manufacture

KLH DVZ-2500... | Answered on Mar 23, 2015


I would fit the same type, unless the schematic shows a change, which clearly it doesn't. However I would be surprised if R42 burnt up alone! Look at the schematic, is R42 linked to any other transistor or part? If so check them if you can.
By the way is R42 a fuseable resistor, for example is the symbol on the schematic or on PC board different to most other resistors?

KLH ASW10-120... | Answered on Mar 16, 2015


If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

KLH Televison &... | Answered on Mar 15, 2015


Yes, the 10-120 can use a L & R low level subwoofer input. You can get a short 6" RCA splitter adapter from Radio Shack for a under $10. (1 female input, 2 male outputs) Alternately, just plug the subwoofer output on your receiver to just the low level R channel on the KLH sub.

KLH Audio... | Answered on Jan 21, 2015


This model has a high failure rate with the power supply board. Typically, power resistors fail, which in turn burns out the big capacitors.

I have not heard of transformers failing though, so it shouldn't be too much to repair it.

Here are the schematics for the unit: Upper board and Lower board

KLH ASW10-120... | Answered on Jan 18, 2015


make sure you have the speaker connection right if you do then it is a ground problem try plugging it in a different outlet

KLH HTA-4906... | Answered on Jan 17, 2015


There is a small plastic plug just above the power cord. Remove it to find the fuse.
http://product-images.highwire.com/4442801/6385-5.jpg

KLH ASW10-120... | Answered on Jan 07, 2015


Most likely the amp in the sub has blown. It will need repair or replacement. I'd take it to an expert in repairing amps, it's not a job for you unless you're experienced in troubleshooting these things.

KLH Audio... | Answered on Jan 01, 2015


I realize that this is an old problem, but folks are still finding it on searches, so here goes.

Here are the two pages of schematics from KLH. I wrote to their tech department and explicitly asked for permission to share them here.

Here's the lower board, which has the power supply:
KLH ASW 10-120 subwoofer schematic - lower board


Here's the upper board:

KLH ASW 10-120 subwoofer schematic - upper board


KLH ASW10-120... | Answered on Oct 19, 2014

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top KLH Experts

The Knight
The Knight

Level 3 Expert

76036 Answers

ray gallant
ray gallant

Level 3 Expert

61843 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a KLH Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...