KitchenAid Recent Questions, Troubleshooting Help & Support

Before you swap it out, get a can of electrical contact cleaner and spray the track and contacts.

https://www.appliancepartspros.com/repair-help/kitchenaid-refrigerator-ksrg25fvms01-repair/ksrg25fvms01-leaking.html

In this video You can see how to replace any component on kitchenaid cooktops! I hope it helps. Thanks! How To Repair Whirlpool KitchenAid Stove Cooktop HD 1080

Mis-wired or the new control panel is faulty. Call them back, it is under repair warranty. The parts aren't cheap! https://www.searspartsdirect.com/model/41v4g0ja62-000593/kitchenaid-kecc667bbl01-electric-cooktop-parts ..

I had this exact same story with my new Whirlpool dishwasher. My daughter fell on the open dishwasher door and afterwards it wouldn't latch closed. After researching online, I learned that 90% of the time it's bent door hinges. At $$130 each, $260 total, I didn't want to replace the hinges. So I removed the hinges, took them downstairs to my shop, put them in the vise and straightened them back with a hammer. Just took a few good, solid hits on each hinge and they were straight again. I installed them back onto the dishwasher and it worked like a charm! Door latches just fine.

igniter failed

There is a Service Manual here Paul. https://www.allrepairmanuals.com/kitchenaid-electric-oven.htm?model_number=KEMC308KSS0+&manual_type=SERVICE ..

The switch that makes it spark?

The dispenser needle valve is not seating properly and correctly causing it to be rinsing and also the aid to be leaking out water.

it is at the bottom on the outside front of the unit.

We are FIXYA dot com, we aren't Kitchen Aid. You error needs a service call, because it probably needs a new control board. These aren't cheap so it needs professional diagnosis. https://www.google.com/search?q=AM71+UI71+EEKGO-010+error+04 ..

This is going to be the best you get.... https://www.partselect.com/Models/KSRG25FKSS05/

The doors are supposed to be offset by the thickness of a quarter. To adjust, use a 5/16" or adjustable wrench to adjust the bolt at the bottom hinge of either door. The doors should be closed when you do this. To raise the height, turn the bolt to the right. To lower it, turn the bolt to the left. Sears Parts Direct has the manuals for the KSC25INS00 here: https://www.searspartsdirect.com/installation-guide/2nnzp1gmgc-000593/kitchenaid-kscs25inss00-side-by-side-refrigerator-parts . See page 9 of the Installation Guide for the information on the door height adjustment. The current link to this manual is https://c.searspartsdirect.com/pd-content/is/content/Sears/L0406508 . I hope this helps. Cindy Wells

sounds like Touch pad/Keypad/Membrane Switch is bad or control panel is bad. You can go online and using your model number search for parts, or have it repaired. If your order parts do you have the skill, knowledge and tools to do job? You could end up throwing parts at it. Personally I would weigh the cost of repair plus the age of unit versus a new one.

Send it back to KitchenAid as per the first review. https://www.bestbuy.com/site/reviews/kitchenaid-2-slice-wide-slot-toaster-contour-silver/1159462 ..

You probably just need a new Shear Pin. This is just a small steel pin like a nail that goes through the gear and the drive shaft. If the strain on the final drive exceeds specs, the pin shears through and thereby saves damage to the gears and motor. Google make model parts diagram https://www.ereplacementparts.com/kitchenaid-4ksm150psbw0-artisan-tilt-head-stand-mixer-parts-c-114958_114959_115458.html This is one of the Shear Pins. They just call it 'pin, retaining'. https://www.ereplacementparts.com/shear-pin-retaining-pin-p-621981.html ..

WE HAVE NO INFORMATION AND SEBSTITUTE PARTS SORRY

Fans running and lights on but no cold or cool air? Is your model the KSRP22FSMS00 listed above your post? Here is a parts manual for your model here=> KSRP22FSMS00.pdf (1761.50 KB) Here is Adobe Reader if your computer does not already have Adobe=> Get Adobe Acrobat Reader Are you able to unplug and your refrigerator remove the back cover that has the access to the compressor? I need to know if the top of the compressor is so hot you cannot keep your hand on its top. This tells me if too hot that the compressor is trying to start and may need start relay and overload. Some models also have run capacitors. If no problems there then this may point to the-> 2304009 Main Control Board When you say the refrigerator is not cooling are you saying only the fresh food section is not cooling but freezer is cooling? Answer these questions and I believe we can find the reason your model is not cooling. First look around the fresh food section door frame for the correct model number, Thanks Sea Breeze

See following video. Fast forward to 7:30 and it shows the on/off contact. Around a minute earlier it shows the the speed lever, spring, and link.

https://youtu.be/Pi8ufwlOtqU

It may need new carbon brushes in the motor, but whether you can get them is another matter. Phone their service department. You may also have lubrication issues that is slowing it down.SALTON CANADACustomer Service Department 81A Brunswick Dollard-des-Ormeaux Quebec, Canada H9B 2J5Website: www.salton.comManual, just because I found ithttps://www.salton.com/wp-content/uploads/2016/04/KM-386-IB-ENweb.pdfhttps://www.google.com/search?q=salton+km386+replacement+carbon+brushes..