Kipor Logo

Kipor Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 26 Products
  • 184 Answers
  • 14K Views

I would try disconnecting the oil pressure sensor temporarily to isolate that circuit as the possible cause of it shutting down.

Kipor Electrical... | Answered on Apr 15, 2019 | 26 views


Give you some suggestion, hope can be helpful for you.
Here is some basic principles for troubleshooting generator faults:
1. Check outside of generator firstly then inside
In the case of generator failure, the possible fault locations outside the electronic control system should be checked firstly. This can avoid a fault that is not related to the electronic control system, but make complex, time-consuming and laborious checking on the sensors, computers, actuators and circuits of the system. The real fault may be easier to find but can not be found.
2. Code priority
Electronic control system generally has fault self-diagnosis function. When some fault occurs in the electronic control system, the fault self-diagnosis system will immediately monitor the fault, and alarm or prompt the operator through warning lights such as "monitoring engine". At the same time, the fault information is stored in code. For some faults, the fault code should be read according to the method provided by the manufacturer before the fault self-diagnosis system is checked, and the fault location indicated by the code should be checked and eliminated. After the failure code refers to the elimination of the fault, if the engine failure phenomenon has not been eliminated, or no fault code output is started, then the possible fault location of the engine is checked.
dsc01081_??-gchmaamodmqy1czm0regslps-1-2.jpg https://www.dieselgeneratortech.com/generator

Kipor Electrical... | Answered on Apr 12, 2019 | 25 views


check the instruction book on your generator - for the exact steps to follow after this icon appears.

Kipor Electrical... | Answered on Feb 10, 2019 | 59 views


id be checking the engine breather if that kept happening. has to be clogged somehow

Kipor Electrical... | Answered on Feb 01, 2019 | 51 views


screenshot_2019-01-25-14-07-29-5m4vg20v4mjgdjzqxftqb5de-2-0.png Qu'est ce qui provoque cet insident

Kipor Electrical... | Answered on Jan 25, 2019 | 1,527 views


If you are in Europe, you run 240 VAC @ 50 Hz. If you are in the U.S., you run 120 or 240 VAC both @ 60 Hz. Assuming that it's NOT an inverter generator, if your engine is running too fast or too slow, your frequency will be too high or too low which can damage sensitive electronics or electric induction motors. Apparently, you have a well controlled / monitored generator. While it is still running during those 20 seconds, I would check for your local voltage at it's output. If it is well above or below it's rated voltage, it's frequency will be out of range also, again, assuming that it's NOT an inverter generator. If it is an inverter type, you'll have to take it to a service center for adjustment. If not and the voltage is out of range, I would try adjusting the engine speed to bring it back into spec. I am in the U.S. My father in law had a craftsman 3,650 watt generator that didn't have the monitoring that yours does but it did the same thing. It would run for 20 or 30 seconds and quit. The oil was up and all looked well. I disconnected the low oil pressure switch and it ran fine. I replaced the switch the next day. I have a 7,000 watt Troy Bilt that I have wired into my house for emergencies but I bought a small, cheap Champion brand 1,400 watt generator for portable use. I brought it home and fired it up and out of the box it was putting out 133 VAC instead of the standard 120. I turned the idle down until it read 120 VAC and it works fine as long as I don't try to run a window A/C unit or fridge. It doesn't have the guts to start the compressor but it works great for lighting, TV's or small hand tools. Good luck.

Kipor Electrical... | Answered on Jan 03, 2019 | 59 views


Generator replacement brush notice:
1, from the model and material needs and the original brush.
2.It is best to grind the new brush to the Radian size of the old brush.
3. pay attention to adjust the brush grip pressure.
4. the carbon brush size should be equal, not too big or too small. The carbon brush is not subject to force in the process of placement.
5. pay attention to the carbon brush and armature to have obvious contact, do not push the carbon brush in.


Generator brush replacement method:
1, the first with a special wrench loose brush braid fastening screws, loose fastening screws should not be loosened excessive, to prevent screw loosening and falling off.

2, take off the carbon brush braid, the carbon brush and the pressure-equalizing spring at the same time. When installing a carbon brush, put the brush into the brush grip.
3, then press the equalizing spring.
4.Use special wrench to fasten the brush and braid to fasten the screw. When fastening the screw, it is not necessary to exert too much force to prevent the screw from being damaged.
5. Check that the brush moves freely in the brush grip, and the spring can be pressed in the center of the brush.

Kipor Generator... | Answered on Nov 01, 2018 | 128 views


Order the service manual from Kipor.

Kipor Electrical... | Answered on Oct 11, 2018 | 92 views



1. Check the voltage of battery whether is 12V or 24V; 2. The voltage of battery is low when the generator is still, then it is necessary to dismantle the battery and charge the battery with charger.
3. If the voltage of battery is low but the generator is running, it indicates that the diesel engine driven charger doesn't work; then it is necessary to stop the engine to check the fan belt.
4. if the fan belt is not loose, please check the charging AC diesel engine driven charger, please refer to Manual for Diesel Engine.
5. If the battery can not store the electricity, please replace the battery for a new one. https://www.dieselgeneratortech.com/generator-sets/discovery-and-elimination-of-faults-of-the-control-system.html

Kipor Electrical... | Answered on Sep 30, 2018 | 412 views


remove the recoil section from the air shroud or if welded on remove the air shroud
If you have never replaced a cord , it may be quicker to take it to any mower shop to have it done as it can be frustrating to get the spring tension correct when winding in the new cord

Kipor Electrical... | Answered on Sep 21, 2018 | 206 views


You most likely have overloaded the unit. There is an overload reset aka circuit breaker on the side that must be reset.

Kipor Electrical... | Answered on Sep 14, 2018 | 164 views


fill the sump to the correct level
check /replace oil level sensor system

Kipor Electrical... | Answered on Jul 22, 2018 | 70 views


Im taking it as the engine is cutting out?
Is this a diesel model?

Try, low oil cut off, fuel tank not vented correcly, fuel blockage.

Kipor Electrical... | Answered on Feb 25, 2018 | 178 views


Is there any circuit breakers or main cut off switch in the off position? If so start the generator and turn on all circuit breakers or cut off switches.

Kipor Electrical... | Answered on Jan 28, 2018 | 811 views


Read the instruction manual. If you are certain you did everything right and the generator does not behave as intended then return it to the supplier as faulty.

Kipor Electrical... | Answered on Jan 27, 2018 | 436 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Kipor Experts

Vernon Taylor

Level 3 Expert

5240 Answers

pawnpower

Level 3 Expert

851 Answers

Wayne McNeil

Level 2 Expert

177 Answers

Are you a Kipor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...