Keurig Logo

Keurig Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 156 Products
  • 6K Answers

I've got a B50 as well, and none of these solutions are quite accurate. The problem is with the ball valve directly above the top needle. You first need to remove the handle by taking out the screw on either side. Mine is some size of torks. Then open the hood and remove the two screws from under it. The hood then lifts right off the body. There is a rubber hose that goes into the top part of the ball valve; this must be removed. You can then use a slightly bent paper clip to reach in carefully and push the ball down to unstick it. It is being pushed up by a spring from underneath, so coming from the bottom with a paper clip just pushed it up tighter in the seat. Once it is clear again, put the hood and handle back on.

I think Keurig should send free replacement valves, maybe better designed as well so they don't stick anymore. If not, I am going to see if I can purchase a replacement.

Keurig B50... | Answered on Mar 19, 2019

Dump it if out of warranty. Or return it to Bed Bsth and Beyond...even if u didn't buy it there. They'll exchange or giv3 u credit for a new one.

Keurig Coffee... | Answered on Mar 10, 2019


Keurig Coffee... | Answered on Mar 09, 2019

Desacle now or it won't reset to factory settings.

Keurig Platinum... | Answered on Mar 03, 2019

Holding down the Auto Off and the both cup sizes worked for me as well. I rcrvcd my answer from Bryan above in the comments section

Keurig B100... | Answered on Mar 01, 2019

The K-Select™ brewer will automatically turn off after 2 hours of idle time. Theauto off feature can be disabled if you wish to keep the brewer on at all times.

1 Answer. To cancel the Auto Off feature: Press the MENU button twice to reach the "AUTO OFF" MENU programming mode. Press and release the blue Left Button under the blinking "H" to advance one hour at a time until "OFF" is displayed.Dec 18, 2017

Keurig Coffee... | Answered on Feb 26, 2019

5 answers
Jun 20, 2010 - There is an "Auto Off" programing capability with this machine that may be the culprit if everything else is working fine. Check the user manual ... SOLVED: My cuisinart coffee maker shuts off after ...
1 answer
Oct 12, 2014
Cuisinart SS-700 single serve coffee maker won't ...
11 answers
Jun 20, 2012
SOLVED: My Cuisinart coffee maker turns off after ...
3 answers
Jun 28, 2010
SOLVED: Coffee maker shuts off during brew cycle
2 answers
Nov 29, 2007
More results from

Keurig Coffee... | Answered on Feb 26, 2019

you found the right place right time buddy.. i know a lot of websites for repairs and manuals that can really help u..

Keurig Coffee... | Answered on Feb 05, 2019

fixya can not sorry

Keurig Coffee... | Answered on Feb 05, 2019

I had a similar problem except there was no water going into the K-cup. I fooled around with the machine for awhile but I had no luck. Figuring I had nothing to lose, I broke out a can of air that one uses to clean computer keyboards. I sprayed the air into the nozzle that puts water back into the reservoir and air came out of the water intake hole but not the needle that puts water into the K-cup. This meant that there was a block between the the needle and the reservoir. I plugged the water intake hole with a towel and my fingers then sprayed the air into the same nozzle. All of a sudden, a large blast of water came out of the needle. The machine worked after this. Just be careful not to put your hand in front of the needle because the water might be hot. Also, unplug your machine before doing any tinkering. Hope this might help some people.

Keurig Special... | Answered on Feb 05, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Keurig Experts


Level 2 Expert

101 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers


Level 2 Expert

218 Answers

Are you a Keurig Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides