Kenmore Washing Machines - Page 6 - Recent Questions, Troubleshooting & Support
I have a Kenmore he2 plus washer model 110.47531702 that will not start
t's possible that there is an issue with the door lock mechanism or the door lock sensor. The fact that the door locks but nothing else happens suggests that the washer is not detecting that the door is locked properly. Here are a few things you can try:
- Check the door lock mechanism: Make sure that the door lock mechanism is clean and free of any debris or obstructions. Try manually engaging and disengaging the door lock a few times to make sure that it is working properly.
- Check the door lock sensor: The door lock sensor is a small switch located near the door lock mechanism. Make sure that it is clean and properly aligned. You can try pressing it manually to see if it is working properly.
- Check the wiring: It's possible that there is a problem with the wiring between the door lock mechanism, the door lock sensor, and the control board. Check the wiring harness for any signs of damage or corrosion.
- Check the control board: If everything else checks out, there may be an issue with the control board. Make sure that it is properly installed and connected. You may also want to try resetting the control board by unplugging the washer for a few minutes and then plugging it back in.
If none of these steps resolve the issue, it may be best to contact a professional appliance repair service for further diagnosis and repair.
Bad smell in washer
The front door seal stays moist an will grow mold. The mold smells and must be removed from the seal. To remove the mold you will need to remove by manipulating the seal to get under it. The mold will stink up you towels and other fabrics that have much of a pile to them. I have run my laundry with an oxygen sanitizer that I use to clean beer brewing equipment. This is the only thing that gets the smell out. Sears has a service flash on this but no solution. You might try leaving the door open so the seal can dry.
Dripping in tub when complete
If your Kenmore washer series 400 model 22102 is dripping water in the tub after the cycle is complete, there could be a few potential causes. Here are some things to check:
- Water valve: The dripping could be due to a faulty water inlet valve. This valve controls the flow of water into the machine and if it's not closing properly, water can continue to drip into the tub even when the cycle is complete. You may need to replace the water inlet valve to fix the issue.
- Water level sensor: Another potential cause of dripping could be a malfunctioning water level sensor. This sensor tells the washer when the tub is full and it's time to stop filling with water. If the sensor is faulty, it may not be accurately detecting the water level, which could lead to dripping. You may need to replace the water level sensor to fix the issue.
- Drain hose: If the washer is not properly draining, it could also lead to dripping after the cycle is complete. Check the drain hose for any kinks or clogs that could be preventing water from draining properly. You may need to clean out the drain hose or replace it if it's damaged.
- Overloading: If you're overloading the washer with too much laundry, it could be causing water to overflow and drip into the tub after the cycle is complete. Make sure you're following the manufacturer's guidelines for load size to avoid overloading the machine.
If you're unsure of how to diagnose or fix the issue, it may be best to consult a professional technician or reach out to the manufacturer for assistance.
Kenmore Top load washer 11022242510 Will not agitate or spin.
There could be several possible causes for your Kenmore top load washer not agitating or spinning. The actuator is one possibility, but it's not the only one. Here are some other potential causes to consider:
Lid switch: The lid switch is a safety feature that prevents the washer from agitating or spinning when the lid is open. If the switch is faulty, it may prevent the washer from agitating or spinning even when the lid is closed. You can test the switch by using a multimeter to check for continuity when the lid is closed.
Drive belt: The drive belt connects the motor to the transmission, which turns the agitator and drum. If the belt is broken or worn, the washer won't agitate or spin. Check the belt for signs of damage or wear, and replace it if necessary.
Motor coupler: The motor coupler connects the motor to the transmission. If the coupler is broken or worn, the washer won't agitate or spin. You can check the coupler by removing the motor and transmission and inspecting the coupler for damage.
Transmission: If the transmission is faulty, it may prevent the washer from agitating or spinning. This is a more serious issue that may require a professional repair.
Based on the symptoms you described, the issue could be with the actuator, but it's hard to say for sure without further testing. The actuator controls the shifting of the transmission from agitate to spin, so if it's not working properly, it could prevent the washer from agitating or spinning. You can test the actuator using a multimeter to check for continuity.
If you're not comfortable diagnosing or repairing your washer yourself, it's best to contact a professional appliance repair service to diagnose and fix the issue.
I have a Kenmore Elite front loader model 42198900 , this morning shut the door ,light stayed on and no power to controls, any ideas
If you have a Kenmore Elite front loader model 42198900 and the door light stays on while the machine has no power to the controls, there are a few potential causes you can investigate:
1. Check the power supply: Make sure the washing machine is properly plugged into an electrical outlet and that the outlet is functioning properly. If the outlet is not working, check the circuit breaker or fuse box to see if a circuit has tripped or blown.
2. Inspect the door lock: The door lock mechanism may be malfunctioning, preventing the machine from turning on. Check to see if the door is closing properly and if the lock is engaging properly. If the lock is faulty, it may need to be replaced.
3. Check the control board: The control board is responsible for sending power to the various components of the washing machine. If the control board is malfunctioning, it can cause issues like a door light staying on but no power to the controls. Check the control board for any signs of damage or wear, and consider having it tested or replaced if necessary.
4. Look for other potential issues: If the above steps do not identify the problem, there may be other issues with the machine that are causing the problem. Consider contacting a professional appliance repair service for further diagnosis and repair.
How to clean Kenmore Elite sm 9711174 washing machine
To clean your Kenmore Elite SM 9711174 washing machine, you can follow these steps:
1. Clean the exterior of the machine: Wipe down the exterior of the washing machine with a damp cloth and mild detergent. Be sure to dry it thoroughly to prevent any water damage.
2. Clean the drum: Mix a solution of 1/4 cup of baking soda and 1/4 cup of water and pour it into the detergent dispenser. Run the machine on the hottest and longest cycle with an extra rinse. This will help to remove any built-up detergent residue or mildew from the drum.
3. Clean the detergent dispenser: Remove the detergent dispenser and soak it in warm, soapy water for 10-15 minutes. Use a soft-bristled brush to scrub away any buildup or debris, and rinse it thoroughly before replacing it.
4. Clean the lint filter: The lint filter is located near the bottom of the machine. Remove it and rinse it under running water to remove any lint or debris. If the filter is particularly dirty, soak it in warm, soapy water for a few minutes before rinsing it.
5. Run a cleaning cycle: Some washing machines have a self-cleaning cycle that you can use to help remove any buildup or mildew. Check the user manual for instructions on how to run a cleaning cycle on your specific machine.
By following these steps, you should be able to clean your Kenmore Elite SM 9711174 washing machine and keep it running smoothly.
Kenmore elite 100 series.. fills with water for wash but drains immediately
If your Kenmore Elite 100 series washing machine is filling with water for the wash cycle but immediately draining without actually washing the clothes, there could be a few potential causes:
1. Faulty or clogged water level pressure switch: The water level pressure switch is responsible for sensing the water level in the tub and signaling the washer to stop filling once the appropriate level is reached. If this switch is faulty or clogged, it may be signaling the washer to drain the water immediately. You may need to replace the pressure switch or clean the hose that connects it to the tub.
2. Clogged drain hose or pump filter: A clogged drain hose or pump filter can prevent the washer from properly draining the water, causing it to immediately drain as soon as it fills. Check for any clogs or blockages in the drain hose or pump filter and clear them if necessary.
3. Broken or faulty drain pump: If the drain pump is broken or not functioning properly, it may not be able to properly drain the water from the washer, causing it to immediately drain. You may need to replace the drain pump if it is broken.
4. Malfunctioning control board: In rare cases, a malfunctioning control board may be causing the washer to immediately drain after filling. If none of the above solutions work, it may be worth having a professional technician inspect and potentially replace the control board.
Washer fills with water, then stops
OBVIOUS REPL LID SWITCH AND SHOULD SOLVE YOURE PROBLEM 100 % MAYBE INSTALLED IN CORRECTLY,, TAKE A LOOK AT YOUR LID MAKE SURE BUMBER IS ON AND NOT TWIKED
I have a Kenmore model 110.25132411 in the rinse cycle only water takes a long time to fill. Then it just drains and doesn't spin.
If your Kenmore washing machine is having trouble filling and then drains without spinning during the rinse cycle, there could be a few possible causes.
- Water supply issue: The first thing to check is the water supply. Make sure the water supply valves are fully open and there are no kinks or blockages in the hoses. Also, check the water pressure and make sure it meets the manufacturer's requirements.
- Faulty water inlet valve: The water inlet valve is responsible for controlling the water flow into the washing machine. If the valve is faulty, it may not be allowing enough water to enter the machine, which can cause the filling to take a long time. It could also be stuck in the drain position, causing the machine to drain instead of filling. You may need to replace the water inlet valve.
- Clogged filter screens: If the filter screens in the water inlet valve are clogged with debris or hard water deposits, it can restrict water flow and cause the machine to fill slowly or not at all. Try cleaning the filter screens to see if this improves the water flow.
- Faulty pressure switch: The pressure switch monitors the water level in the washing machine and tells the control board when to start and stop the filling and draining cycles. If the pressure switch is faulty, it may not be sending the correct signals to the control board, which can cause issues with the filling and draining cycles.
If you have checked the water supply and filter screens and they appear to be working correctly, it may be necessary to replace the water inlet valve or pressure switch. If you are not comfortable performing these repairs yourself, it may be best to contact a qualified appliance repair technician to diagnose and fix the problem.
I am looking for a drive belt (?) for my Kenmore top-loading washing machine, Model 110.4563291.
You can obtain a drive belt for your Kenmore top-loading washing machine, Model 110.4563291, from several sources:
- Sears Parts Direct: They offer parts for Kenmore products and can help you find the correct drive belt for your model.
- Local appliance repair shops: They may have the drive belt in stock or can order it for you.
- Online retailers: Such as Amazon or eBay, offer a wide variety of washing machine parts including drive belts.
It's important to note the model number and the type of drive belt you need to ensure you get the correct part.
Not finding what you are looking for?
