Kenmore Elite is a who range of appliance, but as you are in Kenmore Refrigerators category, let's assume it's that. All questions need full 'make model (what it is)' first 3 words please.
The only easy thing to do would be to make sure the condenser fins are clear of fluff, the compressor is running, the compressor fan is running and the internal circulation fan is running. If it is a fridge with freezer above, a blockage at the back of the freezer due to a failed defrost heater can cause an issue where no cold air drops into the fridge.
The other possibility is low refrigerant gas, but that is not something you can rectify yourself.
Check the condenser coils to determine if they are dirty-if the condenser coils are dirty, clean them. Verify the freezer temperature is set between 0 and 5 degrees Fahrenheit (-18 to -15 Celsius). Verify the refrigerator temperature is set between 34 and 40 degrees Fahrenheit (1 to 5 Celsius).
Kenmore 106 series
The refrigerator holds 13.6 cu. ft. and the freezer 4 cu. ft. This model is;
Width - 32 and 3/4 inches
Depth - 32 and 1/8 inches
Height - 66 and 3/4 inches
..
It sounds like you have a wire that is not connected to the circuit board. You should be able to locate the connection point for the wire by consulting the user manual for your dryer. If the user manual doesn't have the information you need, you may need to contact the manufacturer or an appliance repair technician to help you identify the connection point.
first need the tools and parts to do the job --parts=== tap a line valve --compressor --oil--freon--electric [depending on why comp failed ]------tools=gauges-torch-solder -hand tools --freon recovery ---vacuum pump --multi-meter
Start by taking a look at the lower or back part of your refrigerator. A grille ought to be visible on both parts. There is a strong likelihood the water filter is inside if you observe the grille. Check the upper-right corner of the refrigerator if the grille on the back or lower portion is not visible.https://www.usawaterquality.org/water-filter-on-a-kenmore-coldspot-refrigerator/
Go to an online appliance parts store and enter your model number on the page. You should get at least one exploded parts diagram. Look at the section for the door - the pieces of the hinge mechanism are shown there. Identify the broken piece. The one I looked at (called a "door cam") was a bit over $5, but I didn't provide a link because I don't know what model you have.
The fun part is figuring out how to disassemble the door so you can change the part. There might be a YouTube video showing the procedure. I strongly suggest having someone help you by holding the door while you undo the fasteners. You may be able to disassemble the broken hinge and leave the other in place (check the parts on that one before you order in case that also needs a new piece), but you should still have a helper.
Any good quality kitchen cleaner can be used to clean the outside, but don't use the ones with bleach or those that are an abrasive like Comet because they can cause rust spotting. Then after rinsing, and drying you can treat the stainless steel with stainless steel cleaner, or even Baby Oil.
https://blackappleappliance.com/products/33-french-door-kenmore-795-71033-010
wikiHowhttps://www.wikihow.com > ... > Cleaning Metals
13 steps
1.
Choose a vinegar. Certain vinegars can work better than others. White and cider vinegar works similarly on stainless steel, but cider vinegar leaves a more ...
2.
Check the direction of the grain. Like wood, stainless steel has a grain that will run either vertically or horizontally. Wiping the steel down in the ...
3.
Spray your steel liberally with vinegar. Pour the vinegar in a spray bottle to lightly coat the stainless
..
Yes ....My Kenmore French Door Bottom Freezer (model ...RefrigeratorPro.comhttps://www.refrigeratorpro.com > my-kenmore-frenc...My Kenmore French Door Bottom Freezer (model 795.7730) Is Made By LG!!! by Debbie ... That repairman attributed it to a cracked water filter.and No ...Kenmore 79577302600 User Manual REFRIGERATOR ...UserManual.wikihttps://usermanual.wiki > Kenmore > htmlHome:Kitchen Appliance Parts:Kenmore Parts:Kenmore REFRIGERATOR Manual. ... 795.7730 ¢, 795.7731 ... If your refrigerator does not have a water filter,
If your Kenmore Elite refrigerator model 106.5177 is not cooling properly and you suspect it might be in demo mode, you can follow these steps to try to disable demo mode and troubleshoot the cooling issue:
Check for Demo Mode:
Look for any display indicators or icons on the refrigerator's control panel that indicate it is in demo mode. Refer to the user manual for your specific model to identify these indicators.
Disable Demo Mode:
If you identify that the refrigerator is in demo mode, you will need to disable it. The exact procedure may vary depending on the specific model and control panel. However, a common method is to press and hold a combination of buttons on the control panel simultaneously for a few seconds until the demo mode is turned off. Refer to the user manual for your model to find the correct button combination.
Power Cycle the Refrigerator:
After disabling demo mode, unplug the refrigerator from the power outlet and wait for a few minutes. Then, plug it back in. This power cycle may help reset any settings and restore normal operation.
Temperature Settings:
Make sure the temperature settings for both the refrigerator and freezer compartments are set to the desired levels. Allow some time (usually a few hours) for the refrigerator to reach the proper temperature after adjusting the settings.
Check Condenser Coils:
Ensure that the condenser coils located at the back or underneath the refrigerator are clean and not obstructed by dust or debris. Dirty coils can hinder the cooling efficiency.
Check Door Seals:
Verify that the door seals are intact and sealing properly. Improperly sealed doors can lead to loss of cooling.
Check for Airflow Obstructions:
Make sure that there are no obstructions blocking the airflow to and from the refrigerator, both inside and outside.
Allow Time for Cooling:
Refrigerators typically take several hours to cool down and reach the desired temperature after being powered on or after any adjustments.
Professional Assistance:
If the refrigerator still does not cool properly after attempting these troubleshooting steps, it's recommended to contact Kenmore customer support or a professional appliance technician for further diagnosis and repair.
Remember that electrical appliances can be complex, and improper troubleshooting or repairs can lead to safety hazards or further damage. If you're unsure or uncomfortable with any step, it's best to seek professional assistance.
Reset the ice maker: Check the manual that came with your fridge for instructions on how to reset the ice maker. Many refrigerator models have a reset button or switch that can be used to reset the ice maker.
Check the water supply: Be sure the water supply to the refrigerator has not been turned off or become obstructed. If the water supply is turned off or obstructed, the ice maker will not make ice.
Check for obstructions: Make sure there are no obstructions in the ice maker that would prevent it from making ice. If there is something blocking the ice maker, remove it and try again.
Check the ice maker components: check the components of the ice maker such as the water inlet valve, ice mold thermostat or heater. The problem could be with one of these components and replacing them might solve the problem.
If trying these steps doesn't solve the problem, it might be time to replace the ice maker.
