try this...:)https://www.searspartsdirect.com/manual/36znfoopia-000582/kenmore-10670282990-top-mount-refrigerator-partsTo remove and replace the freezer floor:1. Lift both back "fences" up and out.2. Remove the freezer floor by pulling it out about 1 in.(25.40 mm) with one hand around the air tower section(center back) and one hand at center front.3. Lift up floor at rear until hooks release from cabinet and pullthe floor out the rest of the way.4. Replace the freezer floor by sliding the floor straight in untilthe hooks drop into place at rear of cabinet.5. Replace "fences" by aligning pins with socket in the floor, andpushing down until they snap into place.Best to you.
If you've already replaced the temperature sensor, defrost heater, and main control board on your Kenmore refrigerator model 795.72043.112, and you are still experiencing the r dh error code, there are a few additional possibilities to consider:
Check the defrost thermostat: The defrost thermostat is responsible for regulating the defrost cycle in the refrigerator. If it is faulty or not functioning properly, it could trigger the r dh error code. Inspect the defrost thermostat for any signs of damage or malfunction. If necessary, replace it with a new one.
Examine the wiring and connections: Inspect the wiring and connections related to the temperature sensor, defrost heater, and control board. Loose or damaged connections can interfere with proper communication and cause error codes. Ensure that all connections are secure and undamaged. Consider using a multimeter to test the continuity of the wiring and verify proper functionality.
Verify proper power supply: Check the power supply to the refrigerator, including the outlet and the power cord. Ensure that the refrigerator is receiving stable power without fluctuations or interruptions. Irregular power supply can affect the operation of the control board and trigger error codes. Try plugging the refrigerator into a different outlet or using a voltage stabilizer to eliminate potential power issues.
Seek professional assistance: If you've exhausted the above steps and the r dh error code still persists, it may be best to contact a qualified technician or the Kenmore customer support team for further diagnosis and assistance. They have access to specialized tools and resources that can help identify and resolve complex issues with your specific refrigerator model.
When reaching out to customer support or a technician, provide them with the details of the steps you have already taken and the specific error code you are encountering. This information will help them provide more accurate guidance and solutions tailored to your situation.
I would check with meter the water pressure switch and or the water inlet valve.
Washer fills with water and overflows:The water pressure level switch is a pressure activated switch that is used to determine the correct water level in the tub. This part is normally located behind the control panel and will have a hose or air dome tube that connects it to the tub. On washers that use an electronic control, this switch may be located at the sump area below the tub. As the water fills in the tub it will compress the air in the tube and push against a diaphragm inside the switch. The switch will control the water inlet valve and turn the valve off at the correct water level. If the tube has a leak, not enough pressure may be created to activate the switch and the washer may overfill. If the switch is defective it may also cause the machine to overfill. To determine if the switch is bad, you should first eliminate the air dome hose as a problem. Look for signs of cracks or worn areas on the hose. Remove the hose and submerge in water. Seal one end and blow air into the other end and look for bubbles. Check for an obstruction in the hose as well. If the air dome hose appears to be ok, then the water level switch may be defective.You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube. If the machine starts to wash. the pressure switch is more than likely good ( No wash- then THE DIAPHRAGM IS BAD AND SWITCH HAS TO BE REPLACED). Another test u can make with a multi meter is by testing the prongs individually. # 15,16,17 (don't worry to much bout the numbers IF U GET THEM WRONG) place ur meter prongs on both out side prongs or connectors of the switch. (where the wire plugs into) take note of wether it shows OHMS or infinity ( open or close circuit) ? Now place the meter on the left outside and the middle prong, take note agin what it shows. Now place meter prong on the right outside and the middle prong. Agin take note what reading u get. ( you should actually get a reading of infinity in 1 and a reading of continuity or ohms in the other 2? Now the tricky part. Agin place a small tube or hose into the switch and blow into it, using the meter do the same test agin on all prongs. But now keep the pressure on the switch when u blow into it, in other words use ur tongue on one end of tube to not allow air to escape. When u test it agin now one of the prongs that once read infinity should now show continuity or ohms, and 1 of the other prongs that read ohms should now read infinity or open. The other item to check would be your water inlet valve. Check it for continuity with a multi meter it should show Ohms or a closed circuit. Also check for hard water and debris build up in the screens located on the inlet valve To test it when water is overflowing unplug the unit and see if it still overflows or continues to fill. If it stops when unplugged. Then it is not a water inlet problem but an electrical signal problem going to ur water inlet valve. Possibly from the panel or board. You can also do a live volt test to see if it is getting the full 120 current, but be sure to unplug unit before testing as this is a live test. Also another trick to check the water valve, is to first cut the water off and remove the hoses off the back of the washer. Then one at a time point the hoses inside the washer tub and turn the water back on. If you don't have good water pressure, turn the water back off and remove the strainer that should be in one end of the hose. Inspect the strainer to see if it is stopped up, clean it and reinstall it. Now repeat this test. If you have good water pressure now, reinstall hose and your problem is fixedBy the way my advice is free cuz God is good!
Question edited for clarity.
I presume you want a WIRING diagram? Not much available for that model. Sometimes you will find the service information in a bag taped behind the bottom kickplate or inside the back of the case.
https://www.google.com/search?q=Kenmore+HE2+110.46502700+wiring+diagram
..
The Kenmore Elite 790.9505 range is a kitchen appliance designed for cooking and baking. It features a variety of burners, including a powerful 18,000 BTU Turbo Boil burner and a simmer burner for delicate foods. The oven has a large capacity and offers convection cooking for even baking and roasting. The range also includes a number of convenient features, such as a self-cleaning oven, electronic controls, and a built-in timer. Overall, the Kenmore Elite 790.9505 range is a versatile and high-performing appliance that can help make cooking and baking easier and more efficient.
If you're experiencing an ERR code and flashing lights on your Kenmore dishwasher model 587, it indicates an error or fault in the dishwasher's operation. Unfortunately, without specific details about the error code or which lights are flashing, it's challenging to provide a precise solution. However, you can try the following troubleshooting steps:
1. Check the owner's manual: Refer to the dishwasher's manual for a list of error codes and their meanings. It should also provide troubleshooting steps specific to your model.
2. Power cycle the dishwasher: Turn off the dishwasher by unplugging it from the power outlet or shutting off the circuit breaker that supplies power to it. Leave it disconnected for a few minutes to ensure a complete power cycle. Then, plug it back in or switch the circuit breaker back on.
3. Check for obstructions: Inspect the dishwasher's interior, specifically the spray arms, filters, and drain pump, for any obstructions such as food debris or foreign objects. Clean or remove any blockages that you find.
4. Run a diagnostic cycle: Some dishwashers have a diagnostic mode that can help identify the cause of the error. Refer to the manual for instructions on how to initiate the diagnostic cycle.
5. Contact customer support: If the issue persists or you are unable to determine the cause of the error, it's recommended to reach out to Kenmore customer support or a qualified appliance repair technician. They will be able to provide further assistance and help resolve the problem.
Remember, the specific steps and options may vary depending on your dishwasher model. Consulting the owner's manual is always the best course of action when troubleshooting appliance issues.
Hello. I'm a little confused at the description of the problem. You indicated it, "will not agitate during wash cycle or spin during the spin cycle." But later in your description you indicated, "It will however, drain and spin after wash cycle and during the rinse cycle." I'm not sure if you description was an error but it sounds like you will need to replace the coupling which is part number 285753A.
Visit a local appliance repair shop or parts store that specializes in refrigerator parts. Bring the make and model information of your refrigerator to ensure you get the correct switch. They can assist you in finding the right door push button switch for your specific refrigerator model.
Washing machines will not spin until they have emptied most of the water from the drum.
I would check the outlet pipe is clear and the pump runs with no obstruction first.
