kawasaki Logo

kawasaki Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 2K Products
  • 89K Answers
  • 3M Views

What do you mean by overloaded? Do you mead too high of RPM's? Floating the valves can result in the valves hitting a piston and bending one of them or worse.

kawasaki... | Answered 16 hours ago | 18 views


Bikes of that age only need a few things to run.

Compression
Fuel
A spark at the right time

One of those three is defective?

Compression, check with a compression tester
Fuel, is it clean and fresh. Is it getting to the spark plug, it is wet with gasoline?
A spark at the right time. New spark plug and engine correctly timed. A nice fat blue spark if you put the plug against the cylinder head?

kawasaki... | Answered 3 days ago | 21 views


Hi, Wanda for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.kawasakimotorcycle.org/forum/vintage-motorcyle-info/183913-coil-testing.html How to test Ignition Coils on Motorcycles multi meter Kawasaki 1985 ZX600 Service And Repair Manual OEM Parts for Kawasaki http://mybikemanuals.com/kawasaki

1987 kawasaki... | Answered on Mar 14, 2019 | 24 views


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.kawiforums.com/classics-standards/354849-1990-ninja-600-fork-oil-capacity.html
http://www.motorbikespecs.net/index.dyn?flag=2&model_id=1914544&make=kawasaki
Kawasaki ZX6 ZZR600 90 97 pdf
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki

1994 kawasaki... | Answered on Mar 13, 2019 | 73 views


Hi, Brandon TTY fasteners were first used to clamp together bi-metal components such as aluminum and cast iron engines, and aluminum brake knuckles. TTY fasteners are now found on all kinds of vehicles. Unless the "service manual" specifically states not to reuse the fastener it is ok to use them again.
Buying new bolts may seem expensive. After all, the old bolts still look good, but looks can be deceiving. Reusing the old bolts can cause expensive engine failure. Hence only new bolts can provide the even clamping force needed on today's engines.
Why do we need these torque to yield bolts now? We didn't need them in the 1960?s or 70?s! The simple answer is engine materials are different. Aluminum cylinder heads expand at a different rate than cast iron blocks. As an engine warms up, bolted together parts have to move against each other or slide on their gaskets. Therefore the elastic properties of the torque to yield bolts allow movement between parts yet maintain even clamping loads and sealing.
When a shop manual indicates that a bolt is to be discarded and new ones used, they are almost always torqued to yield bolts.
TTY studs can be identified by sight because of the inset hex head at the end of the stud. Always check the service information to get the right amount of torque for a suspension component TTY or otherwise.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.zxforums.com/forums/mechanical-technical/50858-head-bolts.html
https://www.youtube.com/watch?v=HI8bIxuGT18
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
2001 Kawasaki Ninja ZX 6R Owner Manual

2007 kawasaki... | Answered on Mar 12, 2019 | 19 views


Exhaust Butterfly Valve - RiderForums.com


https://www.riderforums.com/z1k-z750.../58255-ehaust-butterfly-valve.html

May 25, 2010 - I am getting an error code of 63 which tells me it's the. ... 2007 Kawasaki Z1000 w/ Full Race 4-2-1 Akra, PCIII, K&N, Airbox Mod, Engine Ice, ...

Exhaust install = Service code 63???? - KawiForums - Kawasaki ...


https://www.kawiforums.com/2007.../102064-exhaust-install-service-code-63-a.html

Feb 10, 2008 - 8 posts - ‎4 authors
Join Date: Dec 2007. Location: san ... Has anyone had this code show up? If so, was it ... code 63 is the exhaust butterfly servo. Penna zx6r is ...

FI codes - Kawasaki Z1000 Forum: Kawasaki Z1000 Motorcycle Forums


https://www.z1000forum.com/forum/z1000-service.../141042-fi-codes.html

Apr 8, 2014 - 5 posts - ‎3 authors
Hi is it possible to view FI codes on a 2013 z1k gen 3? If yes what's the ... No i have code 39 ecu communication error. My fan comes on as ... FI Code Quick Chart and Z1000 owner Manual (3rd gen ...
1 post
May 14, 2016
FI Light
10 posts
May 11, 2015
F1 light - Page 3
8 posts
May 6, 2013
More results from www.z1000forum.com

And from our M/C Guru Gregg Mahin

for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Ehaust Butterfly Valve
Kawasaki Fault Codes
Kawasaki Z1000 Service Manual
OEM Parts for Kawasaki
Download Manual 2007 Kawasaki Z1000 Owner Manual

kawasaki... | Answered on Mar 11, 2019 | 19 views


the oil injection unit on these skis can fail to test you will need to empty gas tank disconnect oil feed line to inlet manifold
then make a mix of two stroke fuel to the correct ratio say 10 liters. poor in to tank and take ski for a run say 10 minutes let it rest and run again if problem persists

it is possible you have leaking or blown crank case seals you will most likely need a professional to test for
i have provided you a link for free shop manual

kawasaki 2010... | Answered on Mar 10, 2019 | 505 views


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=2001+kawasaki+ZX-6R+Ninja+wiring+diagram&tbm=isch&source=univ&sa=X&ved=2ahUKEwjqopuqjfDgAhWOnFkKHRJ6BHoQsAR6BAgBEAE&biw=1440&bih=757 Kawasaki Motorcycle Wiring Diagrams Kawasaki Ninja ZX 6R Service Manual OEM Parts for Kawasaki Kawasaki Ninja ZX 6R Owner Manual

2001 kawasaki... | Answered on Mar 07, 2019 | 19 views


Hi
We have solution for your kawasaki mule 4010 . if you want workshop manual so please contact us : heavymanual1994@gmail.com


Thank you

kawasaki 2012... | Answered on Mar 06, 2019 | 21 views


Try looking at the main fuse (30amp) on the starter solenoid. Make sure handlebar run switch is to on position - we all do it! and also check battery connections are tight - especially the negative lead.

kawasaki... | Answered on Mar 05, 2019 | 29 views


how old is gas in tank #2? sounds like lousy oily gas. white white smoke or blueish? white white sounds like heavy moisture. blue is oil

kawasaki 2010... | Answered on Mar 04, 2019 | 53 views


Hi, Gabriel and the usual suspects are:
1. Dirty or clogged air filter.
2. Faulty spark plug.
3. Bad Gas.
4. Improper oil level.
5. Improper chain adjustment and lubrication.
6. Low tire pressure.
7. Dirty or contaminated carburetor needs cleaning and tuning.
8. Clogged or faulty fuel pump or injectors.
9. Improper valve adjustment.
10. Slipping clutch.
11. Improper timing.
12. Low compression.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.vn750.com/forum/22-carbs-fuel-system/12631-help-needed-poor-power-after-4000rpm.html
Losing power bogging on Freeway High RPM Scary Help Please KawiForums...
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1997 Kawasaki Vulcan 750 Owner Manual

1997 kawasaki VN... | Answered on Mar 03, 2019 | 28 views


not familiar to your set up but as with any system encluding motor cycle. Get a hose and syphone all that you can out and fill with the proper gas. Start it up...it might be a little harder to start but once you get it started it will clear. I once had a guy fill my car with diesel...supposedly gas and I drove the car a long way then kept stopping up with gas. worked fine....sure did clean the engine.

kawasaki 2012... | Answered on Mar 02, 2019 | 22 views


Google it or go to Kawasaki tech they should be able to help you

kawasaki ZZR 600... | Answered on Mar 02, 2019 | 23 views


Hallo, Andrevalkene voordat je het 's morgens start, trek aan de bougies en ruik ze. Ruiken ze naar benzine? Zijn ze nat? Als dit het geval is, kut u brandstof langs de naald lekken en in de carburateur gaan zitten en de cilinders laten overstromen.
Gebruik een voltmeter op de batterij een uur nadat je de fiets hebt uitgeschakeld. Het moet minimaal 12,6 volt zijn. Controleer het nog een keer in de ochtend. Het moet nog steeds 12,6 volt of meer zijn. Als dit niet het geval is, kan er iets worden weergegeven als de sleutel is uitgeschakeld.
Als het een carbureted fiets is en de omgevingstemperatuur is warm, is het mogelijk dat je je choke / verrijker te veel gebruikt. Probeer het eerst aan te zetten terwijl de choke eerst is uitgeschakeld en probeer dan de choke half en dan volledig te stikken. Als je begint met te veel stikken, zal het overstromen. Nadat het is gestart, schakelt u de choke na 15 - 30 seconden uit en gebruikt u vervolgens het gas om de fiets te laten draaien totdat deze opwarmt. Overmatig gebruik van de choke zal uw bougies roesten.
Een nieuwe set goed geslepen bougies kan veel verschil uitmaken in hoe gemakkelijk een fiets start.
Motoren hebben een rijker brandstofmengsel nodig wanneer ze koud zijn. Een inlaatlek kan ook een hard starten veroorzaken, omdat het uit het lucht / brandstofmengsel leunt.
Nadat je de motor hebt gestart, spuit je wat WD-40 of carb-reiniger rond de verzegeling van het inlaatspruitstuk van de carburateur. Als de RPM verandert, hebt u een inlaatlek.
Klik op de blauwe links hieronder voor meer informatie over uw probleem en waardevolle "GRATIS" downloads die u nodig hebt voor het bekijken of afdrukken. Veel geluk en een fijne dag.
https://www.reddit.com/r/motorcycles/comments/433k4p/ninja_500_wont_start_in_cold_35f_where_do_i_spray
https://www.youtube.com/watch?v=3xNnygqoSaQ
Kawasaki GPX750R ZX750 1987 1991 Repair Service Manual PDF Download... $15
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki

1988 kawasaki... | Answered on Feb 25, 2019 | 72 views


Hi, Anonymous before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
No electrical power on bike KawiForums Kawasaki Motorcycle Forums
Motorcycle won start No lights or anything Problem Solved
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja ZX 6R Owner Manual

1996 kawasaki... | Answered on Feb 25, 2019 | 32 views


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://cruiser.mototribe.com/discuss/vulcan-oil-pump
https://www.youtube.com/watch?v=813ym_dICAg
Kawasaki VN1500 Service Manual
OEM Parts for Kawasaki
Kawasaki Vulcan 1500 Drifter Service Manual
http://mybikemanuals.com/kawasaki free owners manual

2000 kawasaki VN... | Answered on Feb 24, 2019 | 24 views


Hi, Anonymous and the usual suspects are:
1. Installation of a different camshaft.
2. Different exhaust system or "STRAIGHT PIPES"
3. Faulty advance curve.
4. Multiple carburetors not in sync.
5. Improperly installed jet kit or wrong kit.
6. Carburetor internal malfunction.
7. Fuel mixture too rich.
8. Fuel mixture too lean.
9. Extremely dirty air filter.
For more information about your issue and valuable "FREE" downloads that you will need for viewing and printing please click on the blue links below. Good luck and have a wonderful day.
https://www.zx-10r.net/forum/f23/powerband-flat-spot-3-5k-rpms-107157.html
https://www.zx6r.com/zx6r/14282-flat-spot-confuses.html
Kawasaki Ninja ZX 10R Service Manual
OEM Parts for Kawasaki
Kawasaki NINJA ZX 10R User Manual

2008 kawasaki... | Answered on Feb 22, 2019 | 26 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Wayne McNeil

Level 2 Expert

177 Answers

Brad Brown

Level 3 Expert

18002 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...