kawasaki Vehicle Parts & Accessories - Answered Questions & Fixed Issues

Maybe a bad fuse, or relay at least that is a good place to start, Note some cars have more than 1 fuse box.

no headlight and no start. the starter switch is bad. the switched needs to be removed and cleaned and also the guides for the shunt need to be fixed. the overheating of the switch melts the plastic guides and prevents the shunt from sliding up and down. it sticks in the down position and stops the headlight ans starter from working. when you get the switch working again you should put your headlight on a relay to remove the power draw through the switch. Kawasaki ke 100cc wiring schematic Google Search

BAD head gasket. Water pump usually only leaks water on the ground.

yes it is the problam

why do you want to remove your starter.

your clutch fork may be worn

Delaware

Remove the head of the bike as six years a long period there must b some rust. sprinkle brake oil on the pistons and then simply/softly/slowly move the pistons up down. do not try to start it. once the movement u feel easy then clean the plugs, point etc air clearner/filter check the engine oil and then try to start

ENGLISH!

Get a new one! or weld your old one1

I would start with a clean and synchronisation of the carbs just the smallest piece of dirt can cause this

4605, 3615, 2625, 1635

hi im new what do you do

Try:http://www.pdf-manual.com/user-guide-instruction-owner-manual-kawasaki-ke-100-1994-18868.html

A faulty central locking system might be due to several reasons, such as a blown fuse, faulty solenoid, or electrical wiring issues. Also, it's good to remember the fault might not be with the central car locking system but the key fob instead; over time, fobs require battery changes.

4.6 Northstar V8. It is located on the rear of engine (driver side) in front. It is in the the water pump housing cover. Remove air box and intake tube and bottom radiator hose. 2 bolts(believe 10mm) on thermostat housing. These systems are a little finicky about air pockets....so fill slowly and let run at idle until operating temp and let cool and check level.....fill as needed and repeat if needed.

Yes

There doesn't appear to be much available on the trucks. You could contact their support as they seem to have lots of service bulletins available. https://www.google.com/search?q=scania+p230+injector+wiring+diagram ..

See the owners manual page 6 for details G5702V 2009-07 web.pdf (directeddealers.com)

It seems like you're dealing with a technical issue related to a Furuno radar array. If the radar array is not spinning and is emitting a beeping sound, there could be several possible reasons for this problem. Here are a few steps you can take to troubleshoot the issue:

1. Check Power Supply: Ensure that the radar array is receiving proper power. Check the power cables, connections, and any fuses that might be relevant. Make sure the power source is functional and providing the correct voltage.
2. Inspect Mechanical Components: If the radar array won't spin, there could be a mechanical issue with the rotating mechanism. Check for any obstructions or debris that might be preventing the rotation. Lubricate any moving parts if necessary.
3. Connection and Wiring: Examine the connections between the radar array and its control/display unit. Loose or damaged cables could cause communication problems and result in the array not spinning. Ensure all connections are secure and undamaged.
4. Software and Configuration: Sometimes, software settings or configuration options can affect the operation of the radar array. Check the user manual or documentation to ensure that the radar is properly configured. Try resetting the settings to default and see if that resolves the issue.
5. Error Codes or Messages: If the radar is emitting beeping sounds, it might be indicating an error condition. Refer to the user manual or any accompanying documentation for a list of error codes or messages and their meanings. This could help pinpoint the problem.
6. Contact Support: If you've tried the above steps and the issue persists, it might be best to contact Furuno's customer support or a qualified technician for further assistance. They can provide more specific guidance based on the model of your radar array and the symptoms you're experiencing.

Remember, working with electronic equipment requires caution to avoid electrical hazards. If you're not comfortable troubleshooting the issue yourself, it's always a good idea to seek professional help.