Jura Capresso Logo

Jura Capresso Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 98 Products
  • 1K Answers
  • 229K Views

Try using warm water in the watertank, important that the water is not too hot, it can cause leakage in the o-rings in the fluidsytem.
Repeat the procedure a few times, if nothing helps, turn off the machine and wait 1 hour and try again.

If you can`t get around this message, then the flowmeter needs to be changed.

Jura Capresso... | Answered on Apr 10, 2019 | 2,056 views


Open the tap with frother spout off. This happened to mine and I took the frother tip off and opened tap with tip off. Water filled and I closed tap...Machine returned "Ready". I heated water in microwave for three minutes- placed frother tip in hot water and all kinds of gunk came out. Lesson learned- Do a thorough cleaning of frother by immersing it in very hot water at least once monthly- even if you don't use it

Jura Capresso... | Answered on Apr 10, 2019 | 6,300 views


Remove the tray at the front of the machine. Look inside and you will see a rubber flap which separates the right and left side of the machine. Gently lift this to the right and look inside to the left (a small mirror like from a womans compact and a flashlight will help you see in there.) You will find a small circular screen (about the size of a half dollar.)  You need to wipe ALL the coffee grinds off of this screen. That should fix the problem. If you use dark beans, you are probably grinding them to fine and some of the oily residue is sticking to this screen. Try grinding the dark beans more coarsely. Only change the grinder WHEN IT IS GRINDING by adjusting the litlle knob in the box where you place the beans. If the problem started just after changing the filter you may have air in the water line and it needs to be flushed. Try running the tea portion hot water until it clears. These suggestions were given to me by Capresso and actually worked for my machine. Good luck. Gary

Jura Capresso... | Answered on Jan 17, 2019 | 7,715 views


Hi all, I have the exactly same problem on my Gaggenau CM470 however the drip tray is clean and the contacts in the back is also 100% clean.. I wonder if its possible to disable the sensor/switch on a CM470 ?

img_0058-e0ag3skiwqxij25yukiuvad0-5-0.jpeg

img_0061-e0ag3skiwqxij25yukiuvad0-5-2.jpeg

Jura Capresso... | Answered on Nov 23, 2018 | 1,806 views


I just called Jura support and they talked me through this SIMPLE solution and it worked right away. Change the grind setting *while the grinder is a spinning*. If you don’t do it while its spinning nothing will happen.

Don’t hesitate to call Jura - their support team is very good.

800 220 5701

Jura Capresso... | Answered on Nov 10, 2018 | 649 views


https://www.betavalve.com/Product-Detail?prodref=U35D&category=144

Jura Capresso... | Answered on May 31, 2018 | 346 views


Coffee Maker manufacturers rarely sell individual parts for the machine aside from filters and whatnot. I recommend replacing it.

Jura Capresso... | Answered on Mar 21, 2018 | 223 views


First, I'm not JURA technician. But I have worked on similar table top "Super Automatics" You should call your vendor or the MFR for service. Especially if it's still under warranty. There are no customer serviceable parts in this machine.
*** the following is for information only ***
- Water not getting to machine or not sensing that the water tank is already filled.
* There usually some type of float near to middle of the water tank. It's usually white or colored plastic. This 'float' needs to move freely up-down to 'sense' the filled tank. clean the tank and shake it -note the movement of this float. It will need further cleaning if it's stuck (or you will have to replace tank if it's crudded up).
* Re-install tank and fill with filtered water. Turn machine off, count to 15 then turn on again. This usually turns on pump to add water to inner tank. If this does not happen then there is a CPU problem. If it does hums for 5-10 seconds then goes off but no heating then the pump may have an air bubble in line. Try the turn off and on method several times (up to 5) to get the water flowing. If it's still not working then there is a clog in the pump and will need service and/or replacement.
* Since this is a table top machine in which you fill the water tank. Try to use filtered (bottled ok) water. Do Not use Distilled or 100% pure water as this type of water will eat out the metals from your machine! Some places use a water softener as it tends to be better for the machine long term (years).
* Still got problems? Check with vendor or MFR for service or replacement. Most machines of this type do not have serviceable parts or adjustments.
Aloha, ukeboy57

PS: I've noted this tank also uses a water filter (which is probably dry after sitting around for a year as you mentioned.) you will probably have to flush out the air in the filter prior to this unit's pump to work properly. I found a youtube vid that may help:
https://www.bing.com/videos/search?q=s7+Jura+capresso+expresso+not+filling&&view=detail&mid=FA80FAE0243927C50056FA80FAE0243927C50056&&FORM=VRDGAR

Jura Capresso... | Answered on Feb 13, 2018 | 126 views


I had this problem and fixed it. At the bottom of the bean container is a tab that extends about a quarter of the way around. This tab is designed to fit into the base inside a quarter-circle groove that rotates back and forth slightly when the bean container is installed or removed. In my case, the groove on the base was not aligned correctly, so I inserted a blade screwdriver into the groove and rotated it gently in a counter-clockwise direction until it stopped. After this, I could install the bean container as expected.
img_8838-pxx1oxga3q1pezu3ieyunfze-1-0.jpg

Jura Capresso... | Answered on Jan 28, 2018 | 348 views


Probably poor design

Jura Capresso... | Answered on Dec 19, 2017 | 130 views


Defective heating element

Jura Capresso... | Answered on Dec 12, 2017 | 221 views


You can find some detail procedure in this tip below
http://www.fixya.com/support/r5713182-jura_capresso_impressa_f9_malfunction_8
Try it since it have help some other with same problem.

Jura Capresso... | Answered on Oct 26, 2017 | 838 views


NOPE I buy pre-ground coffee

Jura Capresso... | Answered on Sep 30, 2017 | 287 views


The first thing to check is the seating of your water tank. Just a few grains of coffee grounds or dirt underneath the tank are enough to break the watertight seal. Make sure the area under the tank is absolutely clean.

That's always worked for me when I've had the leaking problem.

Jura Capresso... | Answered on Sep 02, 2017 | 261 views


pls DIY the repair. Instructions are easy to follow: https://youtu.be/Sz3fyg-36JQ

Jura Capresso... | Answered on Sep 02, 2017 | 403 views


Did you read the instructions? Did you put water in it? If yes, take it back!

Jura Capresso... | Answered on Aug 15, 2017 | 593 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Jura Capresso Experts

The Knight
The Knight

Level 3 Expert

76036 Answers

markybean

Level 1 Expert

40 Answers

Tom Chichester

Level 3 Expert

51371 Answers

Are you a Jura Capresso Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...