Jura Capresso Coffee Makers & Espresso Machines - Answered Questions & Fixed Issues

Question edited for clarity. Question moved from Misc category. • The grinder can be set during grinding to grind approximately between 5 and 9 seconds, producing a milder or stronger coffee beverage (see chapter 9b) Page 13 https://www.seattlecoffeegear.com/assets/user-manuals/jura/jura-impressa-c5-user-manual.pdf ..

Unfortunately, without being there in person to inspect the machine and its components, it's difficult for me to provide a definitive answer. However, I can offer some general guidance that may help:

1. Consult the user manual: The user manual for your Capresso C3000 should have a diagram or schematic showing the different components and their connections. If you still have the manual, check to see if there's a helpful diagram inside.
2. Look for visual cues: While it can be difficult to identify the tubes by sight alone, there may be visual cues that can help you narrow down which tubes go where. For example, one tube may be thicker or more flexible than the others, or it may have a different color or texture.
3. Experiment with different configurations: If you're unable to find a diagram or visual cues, you may need to experiment with different configurations until you find the correct one. This can be time-consuming and frustrating, but it may be the only option if you're unable to find any other information.
4. Seek professional help: If you're still unable to identify the correct tube configuration, you may want to consider seeking professional help. A qualified technician or repair service may be able to identify the correct configuration and get your machine back up and running.

I hope this helps, and I wish you the best of luck in getting your Capresso C3000 back in working order!

First of all check for the connections. Sometimes a wire is lose and gets pulled off from the button. If that is the case, its pretty easy to handle. You can tighten it by hand or use a soldering iron. If it doesn't work check for any motor, wire or button damage.

I just called Jura support and they talked me through this SIMPLE solution and it worked right away. Change the grind setting *while the grinder is a spinning*. If you don’t do it while its spinning nothing will happen.

Don’t hesitate to call Jura - their support team is very good.

800 220 5701

Hi, I made a video how to fix your Jura step by step, good luck. http://fixandparts.wix.com/nicknicoloudis#!jura-coffee-machine/c15gy

Hi, I made a video how to fix your Jura step by step, good luck... http://fixandparts.wix.com/nicknicoloudis#!jura-coffee-machine/c15gy

You can find some detail procedure in this tip below
http://www.fixya.com/support/r5713182-jura_capresso_impressa_f9_malfunction_8
Try it since it have help some other with same problem.

https://www.betavalve.com/Product-Detail?prodref=U35D&category=144

In my case the brew group is jammed in the down position - so I could not remove the grounds bucket. I think error 8 may be when the motor is stuck (over taxed) or the brew group is out of position. I opened up the right hand side after removing the back with the jura oval key tool https://www.jura-parts.com/ then removed the metal panel with a tiny torx head screwdriver I could manipulate the cog on the screw thread with my hands - it was very tight. Lubricated this and it seems to be working now.

clogged clean with vinegar

On the A1 there is a sensor on the bottom edge of the panel showing the help phone numbers. On other models it may be located behind where the trip tray would be inserted. The sensor detects the presence of the grounds container. Take a paper clip and push up inside the notch holding the sensor. Do this with the machine on. The flap will be withdrawn and everything will fit back in.

Ah the Subaru Impressa with S9 engine. :>D Not quite "says it all" Bryan. So..... Question edited to add the maker and 'what it is', a Coffee Maker. Question moved from Cars and Trucks to Jura Impressa category. When you add a maker, you are offered the correct category, 'Impressa' gives you generic Cars and Trucks. You have a 'Replace Now' message that no one else has! https://www.google.com/search?q=Jura+Impressa+S9+%22replace+now%22 However, try this. Remove the Grounds Bin. Disconnect from the power. Replace the bin, reconnect power. This is your manual https://www.seattlecoffeegear.com/assets/user-manuals/jura/jura-impressa-c9-user-manual.pdf Press CTRL+F, and type 'replace' and press enter. There are 16 mentions. I think it refers to the grounds bin being not fully placed. I have come across this many times, there is a small infra-red sensor or a proximity sensor.

going to get it fixed.

The tap is the dial on the left turn it, then it will turn the tap off. If it is repeating this then it may need to be decalcified.

Used to get the Service 8 with increasing frequency until it almost froze up. Luckily I figured out an easy solution and my 5 year old refurbished C1500 with over 4000 coffees runs like brand new. Here's how:
Take out the grounds tray and reach in to pull back the flap up above where the grounds fall. There is a piston and cylinder thingy behind the flap kind of like a car piston. Take a wad of wet paper towel and shove it up there to clean it out. Then use a dry towel to dry it. Now the secret solution: Take a can of spray pam and point it at the piston and cylinder with the flap pulled back. Give it a couple good shots. Now you just need to get the machine to work that in between the piston and cylinder walls by running the rinse cycle until it frees up. You may have to run it a few times then unplug and let it cool for a couple hours and run it again. The motor overheats if the piston is really stuck so you need to let it cool down. Apparently this is lubricated at the factory with a FDA approved food grease from Dow Corning that needs to be replenished but hey no one is going to die from a little vegetable oil. Some day if it even hints at happening again (It has been 3 months now) I know what to do. Cheers!

Hi, a video how to fix your Jura step by step, good luck... http://fixandparts.wix.com/nicknicoloudis#!jura-coffee-machine/c15gy

On my machine - J6 Capresso, the problem was caused by a crack on one side of the grounds scraper, a plastic paddle attached to the side of the brew group. The scraper is supposed to detect when the tray is full by not returning to the normal position and triggering a sensor that detects that the tray was emptied. When one side was cracked, the scraper was too weak to trigger the sensor. I replaced the scraper ($20 part), and that fixed the problem.

Put your finger on and take it off.

If the machine says TRAY MISSING it's the contacts at the back so clean as other people have stated, you can also use a cardboard nail file to clean the contacts at the back if there really skanky!.

If the machine keeps saying EMPTY GROUNDS even though you have, pull out the tray, look just inside the aparture where the tray goes top right at the front there is a small slot where if you look closely you can see a small white micro switch. This will be probably gunged up with coffee and the switch will be stuck up, get a can of WD40 and squirt a small amount up into the switch then poke the switch with a small screwdriver up and down until it moves smoothly.

Then replace all the bits, sit down, look smug and have a coffee cos you've fixed it!! :0)