Jura Capresso Impressa - Recent Questions, Troubleshooting & Support - Page 7

If you want us to localize the cleaning lady, I suggest to ask for her at the nearest employment office. Probably she is looking for a new job. As an option, you can get a new cleaning lady. Now, if you want to find a site to get parts for your coffee maker, look for it at Jura Parts Jura Capresso Parts and Repairs

Hi Shoba Photo sensor or switch is blocked. Not sure if yours is an Infra Red beam or switch Clean & inspect with flashlight Look for light path (blocked) or moveable part (switch) Actually.... it must use an Infrared Light Emmiter to shine through the grounds holder to the sensor on the other side/ 10 Minute Fix.... I hope

first check the grounds tray as it must go in with the side-tabs (small ridge on each side) in the rear, otherwise it will not seat properly. If that doesn't work give me a shout. gl.

foreign element perhaps the grinder is bad though. First try using a small vacuum that will allow adequate control of vacumming up the bean container. remove all the beans etc. the bean container must be emptied. then look at what the vacuum removed, any foreign objects? if you see 1 or more it's likely fixed. otherwise remove any inside cover/guides in the bean container you should now look directly at the grinder wheels with flashlight, as there may instead be a foreign substance or a defect preventing the grinder from processing the beans. if a defect then it may require factory service. gl

I would say that something has a hole in it, but if it doesn't it might have bad quality, and if it isn't that because the place where you bought it from sells good machines, then it still might have something that went wrong or something was misplaced. I'm not sure either, but that's what i think is the most likely reason. You could always try ask the place manager and ask him if there is anything wrong with your machine. Hope it ind of helped!

Check the main switch is on.. rear bottom left corner.. If still won't turn on, check the fuse in the plug.

Most likely it is a sensor error. you can try to clean the inner parts by removing the tray and carefully with a moist towel wipe the parts gently. If you have a mirror on a stick that's helpful. You may have no other visible choice than to contact Jura Capresso and pay for servicing the unit if memory serves it ran about $250. M

Maybe reading the user's manual you can have a hint? Download it from http://www.ooo.jura.com/home_ooo_x/service_support/download_manual_jura_impressa_s9notc_english.pdf

use distiled water and vinegar to descale

sensor is broken or damaged. look for it, or ask a professional repair office.

Either the funnel flap is damaged, or the microswitch that the funnel works with.

To replace this part you will have to open the jura machine. I found this information out because I had the dreaded error 8 reading on my jura machine which stopped it from making coffee. To disassemble the jura coffee machine you'll need some special tools that I will talk about as I describe how to get to the sensor, make sure you get those tools or something similar. The problem that you are having is the boiler is not heating properly (heating the water properly), so the taste of espresso will not be good. You need a high heating temperature to get good tasting espresso. This generally happens because the thermo sensor went bad and the electronic board is not sensing the proper heat because the thermo sensor went out. 1. Remove the drip tray 2. Remove the water tank 3. Remove the coffee cover and bean hopper cover (aroma cover) 4. Remove the cover for the pre-ground coffee shut 5. Now you will need to remove the cup warning plate that is stainless steel, it is fastened with 2 security screws. You'll need a Newelectronx t15 torx security screwdriver to take them out. 6. Now remove the top plate, there will be 5 screws fastening it down. Again use the Newelectronx t15 torx screwdriver to take them out. Pull it up to release. 7. On the rear end of the machine, you'll need to remove some weird oval head screws. The only place I could find the tool for this oval head screw was in the Newelectronx Coffee Tool Kit Set. Get the oval tool, which is different from the Newelectronx t15 torx bit and remove the next few screws. There are 2 screws - oval head, on the lower backside. Take off the rear back panel. On the left you'll find the mechanical parts. 8. On the boiler, which is the big metal part that is formed like an upside down tear drop. The thermo sensor is attached to the boiler with a screw - again use the Newelectronx security screwdriver to remove the security screw. 9. The thermo sensor connects to the electronic board. Detach the wire from the electronic board. Now the thermo sensor is off. 10. Replace the thermo sensor with a new jura thermo sensor that has the same wire colors. If the wire color is wrong the contact thermo sensor might not perform as it should. 11. Now put the machine back together. Good luck

Hi, I made a video how to fix your Jura step by step, good luck.! http://fixandparts.wix.com/nicknicoloudis#!jura-coffee-machine/c15gy