Jugs Popular Questions, Answers, Tips & Manuals

Do you work here? Claim your company

  • 16 Products
  • 52 Answers
  • 10K Views

Fuse is in control ..Hard to get to I cut the section of the box out to get to fuse figured its going to blow often i was cleaning the wheel with a wet sponge when my fuse blew first week.
3_6_2017_7_28_47_am.jpg

Jugs Lite-Flite... | 2,189 views | 0 helpful votes


There can be two possible reasons for this to occur. The first would be that the pitching machine might need more power than that which is available at home, or the machine might be working for a long time and may have got heated up.

Jugs Small Ball... | 1,173 views | 0 helpful votes


I think it's 70 mph not positive but pretty sure

Jugs Mvp... | 990 views | 0 helpful votes


Pretty sure you can take it to a tire shop and get that done

Jugs Small Ball... | 2,260 views | 0 helpful votes


Are you using the right size fuse I would call jugs and ask them what fuse it takes you could also have a wire that's exposed and touching something metal look for that too

Jugs Small Ball... | 1,965 views | 0 helpful votes


1 1/4 pipe from home depot 24 inches long 30 degree bend 4 inched down

Jugs Small Ball... | 838 views | 0 helpful votes


Get a new motor.

Jugs Small Ball... | 307 views | 0 helpful votes


Take off the cover and make sure the wire is connected to the knob and check the wire maybe it's exposed an not working properly

Jugs Small Ball... | 2,063 views | 0 helpful votes


What's wrong with it need more info

Jugs Small Ball... | 1,375 views | 0 helpful votes


Time to get a new one.

Jugs Small Ball... | 550 views | 0 helpful votes


Look for stripped wires that could be your problem if you find any tape them up with electrical tape

Jugs Small Ball... | 2,151 views | 0 helpful votes


Just had this happen on my machine. Opened up the control box and found center disc capcitor was loose from cold solder joint. However we also found the hot lead for the motor at the wiring block on the circuit board had a cracked solder joint. Simply reheated with solder iron and applied little extra solder and it working again.

Jugs Baseball... | 664 views | 0 helpful votes


You most likely need to use medium grade sandpaper and use it one the tires. They need to be sanded down in order for the machine to shoot the balls out.

Jugs Small Ball... | 808 views | 0 helpful votes


pull off the wheel and run the machine. you will be able to see if the hub is out off balance. if it spins true the you have a rim or tire out. this can be fixed by having a tire shop balance it for you or call Jugs and get a complete replacement,tire and rim ,shipped mounted and balanced.
it is very unlikely that the motor shaft is damaged unless it was droped trying to load it into a truck.
it most like;y is the tire and rim that is out

Jugs Small Ball... | 1,046 views | 2 helpful votes


It could possibly be one of the bearings starting to go, is the machine well used or new?

Jugs Small Ball... | 788 views | 0 helpful votes


it it something to do with the wiring

Jugs Small Ball... | 1,106 views | 0 helpful votes


I just fixed one with the same problem.
10 to 1 odd the brushes are stuck from sitting.
unplug unit.
take off the cover of the motor. 2 -7/16 nuts

there are 4 post one with black wire , white wire , ground and no wire.
you need to take off the two nuts on the one with ground and the one with no wire.
you can then remove the cover which will have the brushes inside.
once removed push the brushes in and out of the sleeve to loosen. spray with some liquid wrench or wd-40 and work back and forth. I took some steel wool and cleaned the copper where the brushes contact.
when you put it back together don't forget the scussion ring. it looks like a couple of potato chips put together. line up the slot on the casing with the nub on the perimeter of the brush housing,
slide it in while lining up the long screws with the holes in the housing. you will need to depress the brushes with a screw driver through the front hole , then slide it in . it will not go in the last 1/8th because of the scussion washer. tighten the nuts on the long screws and the gap will close. if you have the wheel off you can use a phillips screwdriver to hold the oth side , if not just hold the screw on the shaft with channel locks in the middle so you will be able to get the second nut started.

repeat on the other motor and you should be good to go

Joe

Jugs Small Ball... | 1,617 views | 3 helpful votes


brushes are seized. just fixed one just like it

Jugs Small Ball... | 612 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Jugs Experts

edecker

Level 1 Expert

2 Answers

jonspitzfl

Level 1 Expert

1 Answers

Kardoc

Level 3 Expert

4424 Answers

Are you a Jugs Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...