Jet Popular Questions, Answers, Tips & Manuals

It is necessary to change the strap.

Talk to the maker of the chair, you'll probably need to replace the speed controller. You'll need the make, model and serial number of the chair when you contact them.

If by "hole at the bottom" you're talking about the spout that fills the tub, and you must pull up on a knob on the top of the spout, then its an easy and inexpensive fix. The knob is the diverter and the seal is worn out. Replace with a new one you can buy at any hardware store. I suggest you remove the old one and take it with you as there are two pipe sizes. A strap wrench or large pair of channel lock pliers will do the job easily. Just grab the entire spout and twist counterclockwise, OR if there is a small hole on the underside of the spout, then a 1/8 or 3/16 Allen wrench will loosten the set screw that holds the spout on, then just wiggle as you pull on the spout to remove

The Pride Mobility Net 3 ultra has a 3 amp off board charger looks like this and can be purchased from Monster Scooter parts. It plugs into the front of the joystick.http://www.monsterscooterparts.com/24-volt-3-amp-xlr-battery-charger-upg.html

Hi, they have the impeller parts here: Hagen

Sharon, are you sure there are even brushes on that motor to change. You will have to Google search your make and model# repair manual to see what can be done. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

No matter what you have done, the fact remains that the motor is still receiving power!!!!!! And if those are the only two items in the path of power transmission to the motor, then one/both has to be fubar. And until you locate the issue, you can always throw in a toggle switch on the ground line to turn on/off.

Yes not all motors were installed with idea anyone would ever have to work on it. don't forget to blow out the motor with compressed air. do not use any sprays or cleaners!!! I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

More than one sensor. Check this out.... http://troubleshootmyvehicle.com/chrysler/3.9L-5.2L-5.9L/oxygen-sensor-test-1

unplug the charger. Make sure your battery is good. Strege Mobility I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

check connections to controller, may have damage. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Check freewheel levers are in drive position. Controller maybe bad. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

the freewheel lever is not in the drive position on both sides I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Sorry but it sounds like a controller fault, need new controller Strege Mobility I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

use silicone lube on it

It is a misfire code. It mean that there is a misfire on that respective cylinder in the firing order. For example, P0306 means "misfire cylinder 6", P0302 means "misfire cylinder 2" and so on. If your car has one of these codes you need to get it fixed asap. If you choose to drive your car in this condition you will do damage to the catalytic converter.

Visit YouTube and type in there what you require to see a video on. I believe it is better to see it for yourself also for guidance.I hope this helped you Colin

The charger may have a fuse in an off-board charger an on board charge may have fuses in the back by the cables I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

28vdc - 29vdc I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489