Jenn-Air Popular Questions, Answers, Tips & Manuals

think getting in an electrician to check the unit out as it is a safety issue

https://www.searspartsdirect.com/partsdirect/user-manuals/JDR8895AAB-Jenn-air-Parts-JENNAIRCOOKING-manual http://kitchen.manualsonline.com/manuals/mfg/jennair/jdr8895aabsw_1.html

there's a door gasket that seals it not the metal part of the door so you might be able to stick your thumb in there as long as the seal on the door is closing tightly to the frame,when you open the door it should be on a 90 degree angle,before you had new hinges put on the door, most likely the door sagged lower to the floor and didn't close properly,if you think alot of heat is escaping you could have a bad door gasket.so open the door,look at it from the side,it should look like an L or at a 90 degree angle or even up a little,if it is the hinges aren't the problem if you think to much heat is escaping,call whoever did the work for you and have them check the door seal or gasket same thing.you didn't send the model number so i don't know what seal you need,go here and watch video should be similar and you can put your model number in to find correct part http://www.appliancepartspros.com/whirlpool-gasket-oven-door-wpw10162384-ap6016005.html hope this helps you out,if heat is coming out with door closed and you have new hinges this is most likely what's wrong

Unplug for a few hours with doors open to do two things 1 to cool down compressor that got to hot from no fan running and to melt ice off coil in the freezer. There is an internal overload built inside compressor and will stay hot with constant power, thats why you need to unplug. Also check bottom coils where fan is and make sure not blocked with pet hair or debris.

Hello - I cannot give you instruction on how to remove the kit(?) surrounding your microwave. I can provide you with information which may help you decide if arranging for an repair technician authorized to service your JennAir microwave is the best option compared to replacing it. I refer you to the information from Angie's List: https://www.angieslist.com/articles/microwave-repair-and-what-it-costs.htm Best wishes.

Be advised that they are heavy. You may need 2 people to check this. The bracket may have a lip on the wall section that you have to take the weight off of to move it.

The igniter tips need to be adjusted close

Yes replace motor

Hello, Jesse - The information on this website may explain why the electric starter for your gas burners click: https://1stsourceservall.wordpress.com/2015/08/07/why-does-my-stove-keep-clicking-troubleshooting-a-gas-stove-ignitor/ Best wishes.

I would the color grout that matches the counter and yes it is heat resisitant. and it cleans up with a spung. be sure to all extra grout off before it drys

Can you hear the wash pump operating during the cycle? Pump could be faulty or blocked, or the pcb could be at fault

Sounds like you have a bad compressor. Try putting a hard start kit on the compressor and see if that helps, if not might need to change out compressor

there is a big difference between an open circuit and a dead short you will still get a reading indicating a circuit even with a dead short which is your code suggest that you get in a technician to find the code faults as it is costing you money guess replacing

most likely you have bad door hinges if the door doesn't close correctly,i don't know if you know this but alot of parts are no loner available for this model,it must be old,the only thing you can get for the door is the hinges and that's it,you'll need the rest of the model number to get the right hinges you're missing the last two letters,you can go here put your model number in to look up parts. https://www.searspartsdirect.com/model-number/JMW8527CAB/1266/0125300.html go to door and look at part 16 the hinge,hope this helps you out,when you open the door,if it sags down lower to the ground the hinges are bad,when open it should be at a 90 degree angle

your washer has an electrical short most likely from water leaking on circuits most likely you need to replace the control panel on the uper door area unless the unit is leaking below

https://searchmanuals.net/search7/?keyword=%2Bowners+%2Bmanuals&gclid=CjwKCAiAqt7jBRAcEiwAof2uKwzE1jBmBNKl9hqWd4TyeToXsj80tGOrdxRc3s6LGEWtoEA-xsOXLBoCIhQQAvD_BwE

Clean the coil that is next to compressor and should be fine .

Is it a good coil ignition gas oven? If so. Try replacing that part. My guess is it isn't hearing up enough t9 fully open the burner

This is normal on self defrosting models

Heating element I would say but check the seal also.