Jayco Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 288 Products
  • 58 Answers

An adjustment need to be made on both of your slides. Depending on the type of slide, the adjustment would need to be done on the lower outside or by inside through the cabinet and under the bed. Making the adjustments are not difficult, getting to the adjustment points may be another story. One important point is to be careful to NOT over extend the slide, this can put excessive pressure on the wall and cause the fiberglass on the exterior to crack. I found out the hard way. Wether the points for adjustment are on the inside or outside, most likely it will be a combination of push bolt with a locking nut. You will need to adjust the lower part of the slide towards the inside to even up the gap. If you can get an actual measurement of the gap, you will want the bottom gap to be just slightly larger; roughly 1-2 mm or 1/16 to 1/8". Once the gap is corrected, now you will have to make an adjustment on the screw drive or worm gear to adjust how far out the slide moves. For an older unit, like my previous 5th wheel, it was easier to remove the anchor bolts from the floor, manually push the slide out to make the slide flush and then re-anchor the drive. However you may end up adjusting, make sure you do everything slow and gradual, keeping everything even.

When I upgraded my bed from a queen to a king, I had to adjust the entire motor assembly to have it centered on the slide for even pressure. While you have your tools out and working on this, take a few extra minutes to evaluate the foam seal gasket around the inside of the slide. If you see any tears or cracks, no matter how small, go ahead and replace it now to save you time and energy later and prevent outside elements from getting in.

Jayco 2010 Jay... | Answered on Dec 25, 2018


I am guessing this is the link to the manual you are looking for :

Jayco 2013 Jay... | Answered on Mar 17, 2018

usually inside of where water connections are

Jayco 2013 Jay... | Answered on Feb 06, 2018

possibly the cable broke on it .

Jayco 2011 Jay... | Answered on Feb 06, 2018

make sure LP is on if ok look outside where furnace exhaust comes out usually two ports directly inside is furnace probably behind a panel with screws

Jayco 2008 Jay... | Answered on Feb 06, 2018

if power to unit need new electrical for toilet or new toilet

Jayco 2008 Baja... | Answered on Feb 06, 2018

bad sensor or look to see if light switch for steps is on

Jayco 2015 Jay... | Answered on Feb 06, 2018

contact manufacturer they will send you a PDF file

Jayco 2012 Eagle... | Answered on Feb 06, 2018

if bulb good check for voltage at socket maybe corroded if no voltage start checking for loose wires

Jayco 2008 Jay... | Answered on Feb 06, 2018

take the camper to a jayco service center and get the correct replacement items for that camper
then it is a matter of removing all the fitting strips to allow removal of the old canvas and the fitment of the new items
a clue her is to when the new canvas id fitted is to leave the camper opened up and to wet the new canvas with silicon fluid and allow it to dry put before folding it away
why , it stops water coming through the canvas when touched in the rain and prevents mould if folded away when wet

Jayco 2008 Baja... | Answered on Feb 06, 2018

The following electrical components (if so equipped) will only operate when your
RV is connected to shore power: 120 to
12-volt power converter, air conditioner,
120-volt refrigerator, microwave oven, television(s), fireplace and appliances
plugged into convenience receptacles.

The 120-volt AC circuit breakers located in
side the main load center protect all
120-volt wiring and components in the RV fr
om circuit overloads and short circuits.
Should a circuit overload or short circui
t occur the circuit breaker protecting the
affected circuit will "trip" preventing the flow of electricity through that circuit.
If a circuit breaker trips, shut "off"
the appliance on that circuit (i.e., power
converter etc.) and allow the circuit breaker to cool down for a brief period of time.
After the cooling down period, reset the circuit breaker by moving its lever "off" and
then back to the "on" position. If the circuit breaker re-trips or frequently trips,
contact your dealer to have the electrical problem diagnosed and repaired.
A circuit breaker identification label is permanently attached to the inside surface
of the 120-volt load center.
Maintenance and Replacement
At the beginning of camping season, inspect the circuit breakers and replace as
needed. Test by turning each circuit breaker "off" and back "on". Circuit breakers
are wearable parts and must be replaced
as needed, as part of your RV
maintenance. If you have any questions, consult your dealer.
Please contact your dealer for repair assistance when replacing circuit breakers.
The power converter converts 120-volt AC power to useable 12-volt DC power
when the shore power cord is connected to an external power source.
The converter has a built-in protective thermal breaker that will shut it down should
overheating occur. Overheating can be
caused by operating the converter above
its maximum power output for an extended period of time, or by an obstruction to
its ventilation air flow. To reduce converter heat build keep unnecessary 12-volt
lights and motors turned "off"
Keep the converter cooling fins and fan clear of
Inspection and maintenance
If the 12-volt power converter is not working (auxiliary battery not being charged)
check the reverse polarity fuse(s) in the converter fuse panel.
There are no
customer serviceable parts inside the converter case and the
manufacturer's warranty will be void if
the case has been removed
. If you
have further concerns contact your dealer.

Jayco 2013 Jay... | Answered on Feb 06, 2018

If they are blade valves (a T-handle that you pull out and push in) then they are probably your black water (the largest diameter one) and grey water. The third is probably a 2nd black water tank if you have a bath and a half. They often have a separate black water tank.

Jayco 2008 Recon... | Answered on Feb 06, 2018

You'll probably have to crawl under and trace where they go. You could possibly put some dye in one of the grey water tanks (ie: the kitchen sink drain or bathroom sink or shower drain) to figure out where it comes from. The black tank is your toilet drain. It always has the larger diameter pipe going to the valve (usually 2 or 3 inch diameter) The grey water tubing is usually 1 1/2 inch tubing.

Jayco 2008 Recon... | Answered on Feb 06, 2018

It could be part of the DC fuse panel if there is a metal access cover door on it. Otherwise it will be near the battery.

Jayco 2009... | Answered on Feb 06, 2018

drain hole plugged on pan

Jayco 2013 Jay... | Answered on Feb 06, 2018

look on inside of fuse panel should be labeled make sure camera is plugged in at unit maybe came unplugged

Jayco 2013... | Answered on Feb 06, 2018

check for hot wire with cut in insulation either by frame or going through frame probably red or black wire also check lights and plug

Jayco 2014 White... | Answered on Feb 06, 2018

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Jayco Experts

Lawrence Oravetz

Level 3 Expert

10528 Answers


Level 3 Expert

2931 Answers

Renee Knafel-Bullock
Renee Knafel-Bullock

Level 2 Expert

337 Answers

Are you a Jayco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides